관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: Rules and general tolerances for castings using profile tolerancing in a general datum system
| 분야 | ISO/TC 213 : Dimensional and geometrical product specifications and verification |
|---|---|
| 적용범위 | This document specifies the rules for geometrical dimensioning and tolerancing of final moulded parts and parts machined out of moulded parts. It also specifies rules and conventions for the indications of these requirements in technical product documentation and specifies the proportions and dimensions of the graphical symbols to be used. This document provides symbols for identifying the relative completeness of the moulded features and parts. These graphical symbols differ from the graphical symbols for surface texture according to ISO 1302[1], which are notably larger. This document specifies general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part. It also specifies machining allowances and draft angles (tapers) for castings in all cast metals and their alloys produced by various casting manufacturing processes. This document establishes the general principles for presentation of general geometrical tolerances that apply to 2D technical drawings in all disciplines and trades but which are also applicable to 3D applications. NOTE All figures are shown in 2D views only. When cast datum surfaces are machined, this document is not applicable. [1]Cancelled and replaced by ISO 21920-1. |
| 국제분류(ICS)코드 | 17.040.10 : 공차 및 끼워 맞춤 |
| 페이지수 | 50 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 8062-4:2023 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: Rules and general tolerances for castings using profile tolerancing in a general datum system | 2023-05-05 | 표준 |
| 2 | ISO 8062-4:2017 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system | 2017-07-31 | 구판 |
ISO 8062-1:2007 - Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 1: Vocabulary 상세보기
ISO/TS 8062-2:2013 - Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules 상세보기
ISO 8062-3:2023 - Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
