관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables
| 분야 | ISO/TC 44/SC 10 : Quality management in the field of welding |
|---|---|
| 적용범위 | ISO 15610:2003 gives the necessary information to explain the requirements referenced in ISO 15607 concerning the qualification of welding procedures based on tested consumables. In addition, it gives the range of qualification. ISO 15610:2003 applies to arc and gas welding but other fusion welding processes may be accepted if specified. It is limited to application to parent metals that produce acceptable micro structures and properties in the heat affected zone and which do not deteriorate significantly in service. This International Standard is not applicable where requirements for hardness or impact properties, preheating, controlled heat input, interpass temperature and post-weld heat-treatment are specified for the welded joint. The use of ISO 15610.2003 may also be restricted by an application standard or a specification. |
| 국제분류(ICS)코드 | 25.160.10 : 용접 및 용접공의 자질 |
| 페이지수 | 5 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 15610:2024 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables | 2024-03-06 | 표준 |
| 2 | ISO 15610:2023 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables | 2023-02-10 | 구판 |
| 3 | ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables | 2003-10-09 | 구판 |
관련상품이 존재하지 않습니다.
ISO 15614-6:2006 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 6: Arc and gas welding of copper and its alloys 상세보기
ISO 15614-8:2016 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 8: Welding of tubes to tube-plate joints 상세보기
ISO 3834-1:2021 - Quality requirements for fusion welding of metallic materials — Part 1: Criteria for the selection of the appropriate level of quality requirements 상세보기
ISO 3834-2:2021 - Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive quality requirements 상세보기
ISO 3834-3:2021 - Quality requirements for fusion welding of metallic materials — Part 3: Standard quality requirements 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
