관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Instrumentation for Impact Test Part 1 - Electronic Instrumentation
| 분야 | |
|---|---|
| 적용범위 | This SAE Recommended Practice outlines a series of performance recommendations, which concern the whole data channel. These recommendations are not subject to any variation and all of them shall be adhered to by any agency conducting tests to this practice. However, the method of demonstrating compliance with the recommendations is flexible and can be adapted to suit the needs of the particular equipment the agency is using. It is not intended that each recommendation be taken in a literal sense, as necessitating a single test to demonstrate that the recommendation is met. Rather, it is intended that any agency proposing to conduct tests to this practice shall be able to demonstrate that if such a single test could be and were carried out, then their equipment would meet the recommendations. This demonstration shall be undertaken on the basis of reasonable deductions from evidence in their possession, such as the results of partial tests. In some systems, it may be necessary to divide the whole channel into subsystems, for calibration and checking purposes. The recommendations have been written only for the whole channel, as this is the sole route by which subsystem performances affect the quality of the output. If it is difficult to measure the whole channel performance, which is usually the case, the test agency may treat the channel as two or more convenient subsystems. The whole channel performance could then be demonstrated on the basis of subsystem results, together with a rationale for combining the subsystem results together. SAE J211-1 of this SAE Recommended Practice covers electronic instrumentation. SAE J211-2 covers photographic instrumentation. |
| 국제분류(ICS)코드 | |
| 페이지수 | 29 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | SAE J211/1_202208 | Instrumentation for Impact Test Part 1 - Electronic Instrumentation | 2022-08-19 | 표준 |
관련상품이 존재하지 않습니다.
BS EN 17950:2024 - Protective helmets. Test methods. Shock absorption including measuring rotational kinematics. 상세보기
BS EN 13484:2012 - Helmets for users of luges. 상세보기
BS EN 13087-10:2012 - Protective helmets. Test methods. Resistance to radiant heat. 상세보기
PAS 015:2011 - Helmets for equestrian use. 상세보기
ASTM F1952-22 REDLINE - Standard Specification for Helmets Used for Downhill Mountain Bicycle Racing 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
