관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
| 분야 | ISO/TC 44/SC 10 : Quality management in the field of welding |
|---|---|
| 적용범위 | This document specifies quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness ≥ 0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds. Quality levels for beam-welded joints in steel are presented in ISO 13919-1. Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and D. Quality level B corresponds to the highest requirement on the finished weld. Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex B. The quality levels refer to production and good workmanship. This document is applicable to: a) non-alloy and alloy steels; b) nickel and nickel alloys; c) titanium and titanium alloys; d) manual, mechanized and automatic welding; e) all welding positions; f) all types of welds, e.g. butt welds, fillet welds and branch connections; g) the following welding processes and their sub-processes, as defined in ISO 4063: — 11 metal arc welding without gas protection; — 12 submerged arc welding; — 13 gas-shielded metal arc welding; — 14 gas-shielded arc welding with non-consumable tungsten electrode; — 15 plasma arc welding; — 31 oxyfuel gas welding (for steel only). Metallurgical aspects, such as grain size and hardness, are not covered by this document. |
| 국제분류(ICS)코드 | 25.160.40 : 용접이음 |
| 페이지수 | 26 |
| Edition | 4 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 5817:2023 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections | 2023-02-24 | 표준 |
| 2 | ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections | 2014-02-06 | 구판 |
| 3 | ISO 5817:2003/Cor 1:2006 | 2006-02-14 | 구판 | |
| 4 | ISO 5817:2003 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections | 2003-10-21 | 구판 |
| 5 | ISO 5817:1992 | Arc-welded joints in steel — Guidance on quality levels for imperfections | 1992-06-04 | 구판 |
관련상품이 존재하지 않습니다.
ISO 15614-1:2017 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 상세보기
ISO 3059:2012 - Non-destructive testing — Penetrant testing and magnetic particle testing — Viewing conditions 상세보기
ISO 9934-2:2015 - Non-destructive testing — Magnetic particle testing — Part 2: Detection media 상세보기
ISO 9934-3:2015 - Non-destructive testing — Magnetic particle testing — Part 3: Equipment 상세보기
ISO 23278:2015 - Non-destructive testing of welds — Magnetic particle testing — Acceptance levels 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
