관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Gaseous hydrogen — Fuelling stations — Part 5: Dispenser hoses and hose assemblies
| 분야 | ISO/TC 197 : Hydrogen technologies |
|---|---|
| 적용범위 | This document specifies the requirements for wire or textile reinforced hoses and hose assemblies suitable for dispensing hydrogen up to 70 MPa nominal working pressure, in the operating temperature range of −40 °C to 65 °C. This document contains safety requirements for material, design, manufacture and testing of gaseous hydrogen hose and hose assemblies for hydrogen fuelling stations. Hoses and hose assemblies excluded from the scope of this document are the following: 1) those used as part of a vehicle high pressure on-board fuel storage system, 2) those used as part of a vehicle low pressure fuel delivery system, and 3) flexible metal hoses. NOTE 1 This document was developed primarily for hoses and hose assemblies for dispensing high pressure hydrogen from refuelling dispensers to hydrogen vehicles. Requirements for hoses used to deliver hydrogen from a transportable vessel (e.g. trailer) into a buffer storage of a station are addressed in ISO 16964. NOTE 2 Hose assemblies include the hose with connectors on each end (see Figure 1). Each connector has two basic functional elements that are addressed as described below: 1) Coupling to hose. This function is defined by requirements and verified (along with the hose itself) by performance-based tests in this document. 2) Fitting for transition and connection to the piping system or equipment. This function is addressed by reference to appropriate hydrogen equipment standards and piping codes. |
| 국제분류(ICS)코드 |
71.100.20 : 공업용 가스
43.060.40 : 연료 시스템 |
| 페이지수 | 27 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 19880-5:2019 | Gaseous hydrogen — Fuelling stations — Part 5: Dispenser hoses and hose assemblies | 2019-11-18 | 표준 |
| 2 | ISO/DIS 19880-5 | Gaseous hydrogen — Fuelling stations — Part 5: Dispenser hoses and hose assemblies | 초안 |
ISO/DIS 19880-7 - Gaseous hydrogen — Fuelling stations — Part 7: Rubber O-rings 상세보기
ISO 19880-8 - Gaseous hydrogen — Fuelling stations — Part 8: Fuel quality control 상세보기
ISO/FDIS 19880-2 - Gaseous hydrogen — Fuelling stations — Part 2: Dispensers and dispensing systems 상세보기
ISO/DIS 19880-5 - Gaseous hydrogen — Fuelling stations — Part 5: Dispenser hoses and hose assemblies 상세보기
ISO 19880-3:2018 - Gaseous hydrogen — Fuelling stations — Part 3: Valves 상세보기
ISO 19880-1:2020 - Gaseous hydrogen — Fuelling stations — Part 1: General requirements 상세보기
ISO 19880-3:2018 - Gaseous hydrogen — Fuelling stations — Part 3: Valves 상세보기
ISO 17268:2020 - Gaseous hydrogen land vehicle refuelling connection devices 상세보기
ISO 19880-8:2019 - Gaseous hydrogen — Fuelling stations — Part 8: Fuel quality control 상세보기
ISO/TR 15916:2015 - Basic considerations for the safety of hydrogen systems 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
