관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
| 분야 | ISO/TC 61/SC 9 : Thermoplastic materials |
|---|---|
| 적용범위 | ISO 294-1:2017 specifies the general principles to be followed when injection moulding test specimens of thermoplastic materials and gives details of mould designs for preparing two types of specimen for use in acquiring reference data, i.e. type A1 and type B1 test specimens as specified in ISO 20753, and provides a basis for establishing reproducible moulding conditions. Its purpose is to provide consistent descriptions of the main parameters of the moulding process and to establish a uniform practice in reporting moulding conditions. The particular conditions required for the reproducible preparation of test specimens will vary for each material used and are given in the International Standard for the relevant material or are to be agreed upon between the interested parties. NOTE Interlaboratory tests with acrylonitrile/butadiene/styrene (ABS), styrene/butadiene (SB) and poly(methyl methacrylate) (PMMA) have shown that mould design is an important factor in the reproducible preparation of test specimens. |
| 국제분류(ICS)코드 | 83.080.20 : 열가소성 수지재 |
| 페이지수 | 29 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens | 2017-05-10 | 표준 |
| 2 | ISO 294-1:1996/Amd 2:2005 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens — Amendment 2: Methods of determining the hold pressure and hold time | 2005-09-05 | 구판 |
| 3 | ISO 294-1:1996/Amd 1:2001 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens — Amendment 1 | 2001-01-25 | 구판 |
| 4 | ISO 294-1:1996 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens | 1996-12-26 | 구판 |
ISO/DIS 294-5 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy 상세보기
ISO 294-5:2017 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy 상세보기
ISO 294-2:2018 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars 상세보기
ISO 294-4:2018 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage 상세보기
ISO 294-3:2020 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates 상세보기
ISO 2818:2018 - Plastics — Preparation of test specimens by machining 상세보기
ISO 294-2:2018 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars 상세보기
ISO 293:2004 - Plastics — Compression moulding of test specimens of thermoplastic materials 상세보기
ISO 294-3:2020 - Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates 상세보기
KS A ISO 2602(2018 확인) - 시험결과의 통계적 해석－평균의 추정－신뢰구간 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
