관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Steel — Ultrasonic testing of steel flat products of thickness equal to or greater than 6 mm
| 분야 | ISO/TC 17/SC 7 : Methods of testing (other than mechanical tests and chemical analysis) |
|---|---|
| 적용범위 | ISO 17577:2016 specifies a method for the automated and/or manual ultrasonic testing of uncoated steel flat products for internal discontinuities by the pulse echo technique. It is applicable to non-alloyed or alloyed steel flat products, in a nominal thickness range of 6 mm to 200 mm. However, this International Standard may be applied to austenitic and austenitic-ferritic steels, provided that the difference between the amplitude of the noise signal and that of the echo detection threshold is sufficient for the limit fixed. Unless otherwise agreed, for testing of steel flat products for welded steel tubes, ISO 10893‑9 applies. Other techniques of testing (e.g. by transmission) or other test equipment may be used at the manufacturer's discretion, provided that they give identical results to those obtained under the conditions of this International Standard. In the event of a dispute, only the method defined in this International Standard will prevail. Testing of flat products, of thickness less than 6 mm and over 200 mm, may be the subject of special agreements between the parties concerned. Testing is normally carried out in the place of production or on the premises of the supplier. |
| 국제분류(ICS)코드 |
77.040.20 : 금속의 비파괴 시험
77.140.50 : 보통 강제품 및 반제품 |
| 페이지수 | 13 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 17577:2016 | Steel — Ultrasonic testing of steel flat products of thickness equal to or greater than 6 mm | 2016-01-04 | 표준 |
| 2 | ISO 17577:2006 | Steel — Ultrasonic testing for steel flat products of thickness equal to or greater than 6 mm | 2006-09-06 | 구판 |
관련상품이 존재하지 않습니다.
ISO 17640:2018 - Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels, and assessment 상세보기
ISO 5817:2014 - Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections 상세보기
ISO 11666:2018 - Non-destructive testing of welds — Ultrasonic testing — Acceptance levels 상세보기
ISO 23279:2017 - Non-destructive testing of welds — Ultrasonic testing — Characterization of discontinuities in welds 상세보기
ASTM E709-15 - Standard Guide for Magnetic Particle Testing 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
