관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method
| 분야 | ISO/TC 164/SC 3 : Hardness testing |
|---|---|
| 적용범위 | ISO 14577-1:2015 specifies the method of instrumented indentation test for determination of hardness and other materials parameters for the following three ranges: macro range: 2 N ≤ F ≤ 30 kN; micro range: 2 N > F; h > 0,2 µm; and nano range: h ≤ 0,2 µm. For the nano range, the mechanical deformation strongly depends on the real shape of indenter tip and the calculated material parameters are significantly influenced by the contact area function of the indenter used in the testing machine. Therefore, careful calibration of both instrument and indenter shape is required in order to achieve an acceptable reproducibility of the materials parameters determined with different machines. The macro and micro ranges are distinguished by the test forces in relation to the indentation depth. Attention is drawn to the fact that the micro range has an upper limit given by the test force (2 N) and a lower limit given by the indentation depth of 0,2 µm. The determination of hardness and other material parameters is given in Annex A. At high contact pressures, damage to the indenter is possible. For this reason in the macro range, hardmetal indenters are often used. For test pieces with very high hardness and modulus of elasticity, permanent indenter deformation can occur and can be detected using suitable reference materials. It is necessary that its influence on the test result be taken into account. This test method can also be applied to thin metallic and non-metallic coatings and non-metallic materials. In this case, it is recommended that the specifications in the relevant standards be taken into account (see also 6.3 and ISO 14577‑4). |
| 국제분류(ICS)코드 | 77.040.10 : 금속의 기계적 시험 |
| 페이지수 | 46 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 14577-1:2015 | Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method | 2015-07-08 | 표준 |
| 2 | ISO 14577-1:2002 | Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method | 2002-10-10 | 구판 |
| 3 | ISO/DIS 14577-1 | Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method | 초안 |
ISO/DIS 14577-6 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 6: Instrumented indentation test at elevated temperature 상세보기
ISO/DIS 14577-1 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method 상세보기
ISO/DIS 14577-2 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 2: Verification and calibration of testing machines 상세보기
ISO/DIS 14577-3 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 3: Calibration of reference blocks 상세보기
ISO 14577-2:2015 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 2: Verification and calibration of testing machines 상세보기
ISO 14577-4:2016 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 4: Test method for metallic and non-metallic coatings 상세보기
ISO 14577-2:2015 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 2: Verification and calibration of testing machines 상세보기
ISO 14577-3:2015 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 3: Calibration of reference blocks 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
