관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Sampling procedures for inspection by attributes — Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
| 분야 | ISO/TC 69/SC 5 : Acceptance sampling |
|---|---|
| 적용범위 | ISO 2859-5:2005 contains sequential sampling schemes that supplement the ISO 2859-1 acceptance sampling system for inspection by attributes, whereby a supplier, through the economic and psychological pressure of lot non-acceptance, can maintain a process average at least as good as the specified acceptance quality limit, while at the same time provide an upper limit for the risk to the consumer of accepting the occasional poor lot. The sampling schemes defined in ISO 2859-5:2005 are applicable, but not limited, to the inspection of: end items, components and raw materials, operations, materials in process, supplies in storage, maintenance operations, data or records, and administrative procedures. These schemes are designed to be applied to a continuing series of lots, that is, a series long enough to permit the described switching rules to be applied. These switching rules provide: a) enhanced protection to the consumer (by means of tightened sampling inspection criteria or discontinuation of sampling inspection) should deterioration in quality occur; and b) an incentive, at the discretion of the responsible authority, to reduce inspection costs (by means of reduced sampling inspection criteria) should consistently good quality be demonstrated over time. The individual sampling plans are not designed to be applicable outside of the schemes in which they are presented. If lots are produced in isolation or in a series too short for ISO 2859-5:2005 to apply, the user is advised to consult ISO 2859-2 for appropriate sampling plans. |
| 국제분류(ICS)코드 | 03.120.30 : 통계적 방법의 응용 |
| 페이지수 | 43 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 2859-5:2005 | Sampling procedures for inspection by attributes — Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection | 2005-06-27 | 표준 |
ISO/DIS 2859-1 - Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 상세보기
ISO 2859-0:1995 - Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system 상세보기
ISO 2859-1:1999 - Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 상세보기
ISO 2859-1:1999/Cor 1:2001 - Sampling procedures for inspection by attributes -- Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection -- Technical Corrigendum 1 상세보기
ISO 2859-3:2005 - Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
