관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 4: Test method for metallic and non-metallic coatings
| 분야 | ISO/TC 164/SC 3 : Hardness testing |
|---|---|
| 적용범위 | ISO 14577-4:2007 specifies a method for testing coatings that is particularly suitable for testing in the nano/micro range applicable to thin coatings. This test method is limited to the examination of single layers when the indentation is carried out normal to the test piece surface, but graded and multilayer coatings can also be measured in cross-section if the thickness of the individual layers or gradations is greater than the spatial resolution of the indentation process. The test method is not limited to any particular type of material. Metallic, non-metallic and organic coatings are included in the scope of ISO 14577-4:2007. The application of ISO 14577-4:2007 regarding measurement of hardness is only possible if the indenter is a pyramid or a cone with a radius of tip curvature small enough for plastic deformation to occur within the coating. The hardness of visco-elastic materials, or materials exhibiting significant creep will be strongly affected by the time taken to perform the test. |
| 국제분류(ICS)코드 | 77.040.10 : 금속의 기계적 시험 |
| 페이지수 | 24 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 14577-4:2016 | Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 4: Test method for metallic and non-metallic coatings | 2016-10-26 | 표준 |
| 2 | ISO 14577-4:2007 | Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 4: Test method for metallic and non-metallic coatings | 2007-05-15 | 구판 |
ISO/DIS 14577-6 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 6: Instrumented indentation test at elevated temperature 상세보기
ISO/DIS 14577-1 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method 상세보기
ISO/DIS 14577-2 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 2: Verification and calibration of testing machines 상세보기
ISO/DIS 14577-3 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 3: Calibration of reference blocks 상세보기
ISO 14577-1:2015 - Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 1: Test method 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
