관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3-1: Vehicle connector, vehicle inlet and cable assembly for DC charging intended to be used with a thermal management system
| 분야 | TC 23/SC 23H : Plugs, Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles |
|---|---|
| 적용범위 | IEC TS 62196-3-1:2020(E) applies to accessories and cable assemblies with the same configuration as specified in IEC 62196-3:2014 with rated operating voltage not exceeding 1 500 V DC and a rated current not exceeding 500 A that employ - thermal sensing, or - thermal transport and thermal sensing with the system architecture described in 4.101. These accessories and cable assemblies are intended to be used in conductive charging systems for circuits specified in IEC 61851-23. NOTE Edition 2 of IEC 61851-23 is under development. The accessories covered by this document are intended to be used in charging mode 4 according to IEC 61851-1. These accessories are intended to be connected to cables according to the IEC 62893 series for DC cables. |
| 국제분류(ICS)코드 |
43.120 : 전기차 및 부분품
29.120.30 : 플러그. 소켓-아우트랫. 연결기 |
| 페이지수 | 62 |
| Edition | 1.0 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | IEC TS 62196-3-1:2020 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3-1: Vehicle connector, vehicle inlet and cable assembly for DC charging intended to be used with a thermal management system | 2020-03-26 | 표준 |
IEC 62196-6:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 6: Dimensional compatibility requirements for DC pin and contact-tube vehicle couplers intended to be used for DC EV supply equipment where protection relies on electrical separation 상세보기
IEC 62196-1:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements 상세보기
IEC 62196-1:2022 CMV - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements 상세보기
IEC TS 62196-4:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 4: Dimensional compatibility and interchangeability requirements for DC pin and contact-tube accessories for Class II or Class III applications 상세보기
IEC 62196-2:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories 상세보기
IEC 62752:2016+AMD1:2018 CSV - In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD) 상세보기
IEC 62196-2:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories 상세보기
IEC 62196-3:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility requirements for DC and AC/DC pin and contact-tube vehicle couplers 상세보기
IEC 62196-6:2022 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 6: Dimensional compatibility requirements for DC pin and contact-tube vehicle couplers intended to be used for DC EV supply equipment where protection relies on electrical separation 상세보기
KS R IEC TS 62196-3-1 - 플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제3-1부: 열관리시스템과 같이 사용하기 위한 직류 충전용 자동차 커넥터, 자동차 인렛 및 케이블 어셈블리 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
