관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Installation code for hydronic heating systems
| 분야 | |
|---|---|
| 적용범위 | Preface This is the fourth edition of CSA B214, Installation code for hydronic heating systems. It supersedes the previous editions, published in 2012, 2007, and 2001.? The main changes from the previous edition are as follows:? a) clarification of the use of storage-type dual-purpose water heaters;? b) clarification of oxygen diffusion barriers;? c) clarification of requirements for hydronic fluid quality;? d) inclusion of polyethylene of raised temperature (PE-RT) tubing and tubing fittings;? e) clarification of requirements for return-water low-temperature protection;? f) clarification of insulation requirements;? g) clarification of requirements for tube fasteners;? h) inclusion of snow and ice melting systems as stand-alone systems;? i) clarifications of auxiliary systems;? j) clarification of radiant under-floor heating and floor surface temperatures;? k) revisions to nominal tube sizing in Table 1;? l) revisions to loop lengths for snow and ice melt systems in Table 3;? m) inclusion of Annex C with guidelines related to radiant surface cooling; and? n) inclusion of Annex D with guidelines related to minimum flow rates for heat distribution.? Scope 1.1 This Code sets out the minimum provisions for the installation, extension, alteration, and renewal of hydronic heating systems.? 1.2 This Code applies to open and closed hydronic heating systems. These systems include? a) hydronic space heating;? b) radiant heating (wall, floor, ceiling);? c) convectors;? d) fan coils;? e) combination potable water heating and space heating (combo) systems;? f) integrated mechanical systems;? g) indirect-fired domestic water heating;? h) pool and spa heating;? i) snow and ice melt systems; and? j) other auxiliary systems.? 1.3 The terms "pipe" and "piping", as well as "tube" and tubing", are used interchangeably in this Code, unless otherwise stated.? 1.4 In this Code, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Code; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Code.? Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.? Notes to tables and figures are considered part of the table or figure and may be written as requirements.? Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.? 1.5 The values given in SI units are the units of record for the purposes of this Code. The values given in parentheses are for information and comparison only. ? |
| 국제분류(ICS)코드 | |
| 페이지수 | 60 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B214-22 | Standard Test Method for Sieve Analysis of Metal Powders | 2022-09-01 | 표준 |
| 2 | ASTM B214-22 REDLINE | Standard Test Method for Sieve Analysis of Metal Powders | 2022-09-01 | 표준 |
| 3 | CSA B214:21 | Installation code for hydronic heating systems | 2021-01-01 | 표준 |
| 4 | ASTM B214-16 | Standard Test Method for Sieve Analysis of Metal Powders | 2016-04-01 | 구판 |
| 5 | ASTM B214-16 REDLINE | Standard Test Method for Sieve Analysis of Metal Powders | 2016-04-01 | 구판 |
| 6 | B214-16 | Installation code for hydronic heating systems | 2016-01-01 | 표준 |
| 7 | ASTM B214-15 | Standard Test Method for Sieve Analysis of Metal Powders | 2015-10-01 | 구판 |
| 8 | ASTM B214-07(2011) | Standard Test Method for Sieve Analysis of Metal Powders | 2011-10-01 | 구판 |
| 9 | ASTM B214-07 | Standard Test Method for Sieve Analysis of Metal Powders | 2007-01-01 | 구판 |
| 10 | ASTM B214-99 | Standard Test Method for Sieve Analysis of Metal Powders | 1999-04-10 | 구판 |
관련상품이 존재하지 않습니다.
N286.3-99 (R2004) - Construction Quality Assurance for Nuclear Power Plants Published by CSA Group in 1999, Reaffirmed in 2004, Withdrawn 상세보기
C22.2 NO. 178-1978 (R2006) - Automatic Transfer Switches 0 Edition, Published by CSA Group in 1978, Reaffirmed in 2006, Withdrawn 상세보기
SPE-2000-94 - Guide for Electrical Equipment for Installation and Use in Canada 상세보기
CAN/CSA-C867.2-09 (R2014) - Performance of decorative light strings.Published by CSA Group in 2009, Reaffirmed in 2014, Withdrawn 상세보기
N292.0-14/N292.3-14 PACKAGE - Consists of N292.0-14, General principles for the management of radioactive waste and irradiated fuel and N292.3-14, Management of low- and intermediate-level radioactive waste 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
