관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Dispensing systems and components for fueling hydrogen powered industrial trucks
| 분야 | |
|---|---|
| 적용범위 | Preface This is the first edition of CSA HPIT 2, Dispensing systems and components for fueling hydrogen powered industrial trucks. ? Scope 1.1 This Standard applies to: a) the mechanical and electrical features of dispensers, which includes the control system and any ancillary equipment, used to dispense compressed hydrogen gas for hydrogen powered industrial trucks (HPITs) used for mobility/propulsion in a non-public application; b) systems that refuel hydrogen powered industrial vehicles to a service pressure of 25 and 35 MPa at a refueling rate of no more than 33 g/second. 1.2 The requirements of this Standard are not intended to constrain innovation. When considering fuels, materials, designs, or constructions not specifically dealt with in this Standard, these alternatives are to be evaluated as to their ability to yield levels of safety and performance equivalent to or better than those prescribed by this Standard. 1.3 A hydrogen powered industrial truck (HPIT) is an electric industrial truck that is powered by a fuel cell system. These vehicles include the following: a) electric fork lift trucks; b) airport tuggers; c) yard trucks; d) refrigerated trucks (reefer units); and e) auxiliary power units (APUs). 1.4 This Standard does not apply to dispensers intended for the refueling of automotive vehicles or heavy duty surface vehicles. Note: HPIT dispenser should not be used to refuel vehicles requiring SAE J2601-1 or SAE J2601-2 fueling protocols. 1.5 This Standard does not apply to residential fueling appliances. 1.6 In the case of conflict between this Standard and Federal, Provincial, State, or Local requirements, the governmental requirements take precedence. 1.7 This Standard contains SI (Metric) units with corresponding yard/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding valve in other units are both specified as a quoted marking requirement, the first stated unit, or both are to be provided. Note: IEEE/ASTM SI 10 or ISO 80000-1 was used as a guide in making metric conversions to yard/pound quantities. 1.8 All references to pressure throughout this Standard are to be considered gauge pressure unless otherwise specified. 1.9 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. |
| 국제분류(ICS)코드 | |
| 페이지수 | 82 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | CSA HPIT 2:17 (R2021) | Dispensing systems and components for fueling hydrogen powered industrial trucks | 2017-01-01 | 표준 |
관련상품이 존재하지 않습니다.
CSA/ANSI HGV 4.9:20 - Hydrogen fueling stations 상세보기
ANSI/CSA AMERICA FC 3-2004 (R2021) - Portable Fuel Cell Power Systems 상세보기
ANSI/CSA HGV 4.8-2012 (R2023) - Hydrogen gas vehicle fueling station compressor guidelines 상세보기
CSA HPIT 1:15 (R2020) - Compressed hydrogen powered industrial truck on-board fuel storage and handling components 상세보기
CSA/ANSI HGV 4.3:19 - Test methods for hydrogen fueling parameter evaluation 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
