CSA A370:14 (R2023) Connectors for masonry

관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.

PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)

PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

표준 판매

CSA A370:14 (R2023)

Connectors for masonry

- 발행일 : 2014-01-01
- 발행기관 : CSA

언어	제공형태	판매가격	선택
영어	보안PDF	131,400원

장바구니 담기

상품이 장바구니에 담겼습니다.

장바구니로 이동

상세정보

분야
적용범위	Preface This is the fourth edition of CSA A370, Connectors for masonry. It supersedes the previous editions published in 2004, 1994, and 1984. Significant changes in this edition include the following: a) New requirements on fastener materials (Clause 4.1.2) have been added. b) References to typical designs have been removed as requirements and moved into notes regarding wall anchors with reference to CSA S304 (Clause 7.2). c) Significance of misalignment on ultimate strength has been recognized in a new note (Clause 9.2.2.3, Note 2). d) Application of free play to typical load-deformation curve has been demonstrated by added content to Figure 9.1. e) Editorial changes in the terminology within this Standard address concerns that previous use of "embedment" may be interpreted to require the suspension of the connector within the mortar between masonry units (i.e., mortar placed below and above the connector), whereas standard construction practice often results in the connector being placed directly on the masonry unit and then covered in mortar. f) Harmonization of terminology related to the use of "Tie" and "Connector" throughout standard. g) New requirements for fasteners (Clause 10.7) have been added. h) Updated Figures in the Annexes. i) Expanded guidance has been added on Connectors in Annex A in regards to the Standard now recognizing connectors and prescriptive connectors. j) Additional information has been provided in Annex C on contact between different metals (Clause C.6). k) Annex E has been updated for current Annual driving rain indices. This Standard should be read in conjunction with CSA S304, Design of masonry structures, and CSA A371, Masonry construction for buildings. Scope Notes: 1) For requirements pertaining to loads acting on connectors, see CSA S304. 2) For requirements pertaining to installation of masonry connectors, see CSA A371. 1.1 This Standard specifies minimum requirements for designing the following masonry connectors: a) ties used to i) interconnect the wythes of a masonry wall; or ii) attach masonry veneer to its structural backing; b) anchors used to i) connect masonry walls to intersecting walls or to other structural members; ii) attach stone to its structural backing; or iii) interconnect stone; c) fasteners used to secure a masonry tie or anchor to a structural member, or to interconnect components of a multi-component tie or anchor; and d) repair connectors used to restore or improve masonry construction. 1.2 This Standard does not apply to a) connectors for i) precast concrete; and ii) prefabricated masonry panels; and b) fasteners used to attach equipment or fixtures to buildings. 1.3 This Standard recognizes two types of masonry connectors: a) connectors, including repair connectors, designed in accordance with the performance requirements of this Standard; and b) prescriptive connectors, which offer a simple prescriptive solution (or deemed-to-comply solution) to the performance requirements of this Standard when complying with the stated limiting conditions for use. 1.4 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.
국제분류(ICS)코드
페이지수	91
Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM A370-24a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2024-10-15	표준
2	ASTM A370-24a REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2024-10-15	표준
3	ASTM A370-24 REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2024-03-01	구판
4	ASTM A370-24	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2024-03-01	구판
5	ASTM A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2023-09-15	구판
6	ASTM A370-23 REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2023-09-15	구판
7	ASTM A370-22 REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2022-10-01	구판
8	ASTM A370-22	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2022-10-01	구판
9	ASTM A370-21	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2021-11-01	구판
10	ASTM A370-21 REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2021-11-01	구판
11	ASTM A370-20	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2020-08-01	구판
12	ASTM A370-20 REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2020-08-01	구판
13	ASTM A370-19	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2019-07-01	구판
14	ASTM A370-19e1	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2019-07-01	구판
15	ASTM A370-18	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2018-12-01	구판
16	ASTM A370-17a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2017-11-15	구판
17	ASTM A370-17a REDLINE	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2017-11-15	표준
18	ASTM A370-17	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2017-01-01	구판
19	ASTM A370-16	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2016-05-01	구판
20	ASTM A370-15	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2015-11-01	구판
21	ASTM A370-14	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2014-05-15	구판
22	CSA A370:14 (R2023)	Connectors for masonry	2014-01-01	표준
23	ASTM A370-13	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2013-11-15	구판
24	ASTM A370-12a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2012-10-15	구판
25	ASTM A370-12	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2012-03-15	구판
26	ASTM A370-11a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2011-11-15	구판
27	ASTM A370-11	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2011-05-01	구판
28	ASTM A370-10	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2010-06-15	구판
29	ASTM A370-09ae1	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2009-06-01	구판
30	ASTM A370-09a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2009-06-01	구판
31	ASTM A370-09	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2009-01-01	구판
32	ASTM A370-08b	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2008-10-15	구판
33	ASTM A370-08a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2008-04-14	구판
34	ASTM A370-08	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2008-04-01	구판
35	ASTM A370-07b	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2007-11-01	구판
36	ASTM A370-07a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2007-06-01	구판
37	ASTM A370-07	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2007-04-01	구판
38	ASTM A370-06	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2006-11-01	구판
39	ASTM A370-05	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2005-05-01	구판
40	ASTM A370-03a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2003-06-10	구판
41	ASTM A370-03	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2003-06-10	구판
42	ASTM A370-02e1	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2002-01-10	구판
43	ASTM A370-02	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2001-12-10	구판
44	ASTM A370-01	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2001-12-10	구판
45	ASTM A370-97a	Standard Test Methods and Definitions for Mechanical Testing of Steel Products	2001-12-10	구판
46	ASTM A370-94	Standard Test Methods and Definitions for Mechanical Testing of Steel Products		구판
47	ASTM A370-68	Standard Methods And Definitions For Mechanical Testing Of Steel Products		구판

관련상품

관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품

함께 구입한 상품이 존재하지 않습니다.
추천 상품

IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기

IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기

KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기

KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기

KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기

해외표준

CSA A370:14 (R2023)

상세정보

이력정보

관련상품

다른 사람이 함께 구입한 상품

추천 상품

전체서비스 보기