관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
General Instructions (PTC 1 - 2011)
| 분야 | PTC : Performance Test Code |
|---|---|
| 적용범위 | There is a newer edition of this document available. PTC 1, General Instructions, provides direction to users and code-writing committees of Performance Test Codes. Code?s users shall consider it as part of each test. The objectives of PTC 1 are to define the purpose and scope of ASME Performance Test Codes, to list major industry applications where PTCs can be used, and to provide direction on the use of equipment Performance Test Codes concerning the planning, preparation, implementation, and reporting of test results. Most ASME Performance Test Codes are applicable to a specific type of equipment defined by the Code. There may be several subcategories of equipment covered by a single Code. Types of equipment for which PTCs apply can be classified into five broad categories: (a) electrical or mechanical power producing; (b) combustion and heat transfer; (c) fluid handling; (d) emission control, and; (e) allied equipment. The quantities, which characterize performance, defined in each code for the equipment within its scope. Performance characteristics determined by adherence to a PTC can be evaluated as compared to design or predicted characteristics, to previous test results, or they can be used to benchmark or ascertain performance at a particular time. Some PTCs are written as general documents for reference, in support of the equipment PTCs. These can be considered as technical reference material for the equipment codes. Reference material codes can be divided into three types. The first type addresses the measurement of phenomena closely associated with the equipment, such as emissions. The second type covers instrumentation used in the measurement of thermodynamic or process fluid parameters, such as pressure, temperature, flow, and steam quality, and how to analyze the uncertainties associated with measurement of all primary parameters to develop overall test uncertainty is included in this type. Such individual codes referring to process or thermodynamic quantities are known as Performance Test Code Instruments and Apparatus Supplements. They are supplementary to the information on mandatory instrumentation requirements contained in the equipment codes. Instrumentation information in equipment test codes can supersede the information given in these supplements, or these supplements may be referenced by an equipment Test Code where deemed appropriate by the committee. The third type covers miscellaneous general information, and currently consists of PTC 1and PTC 2, "Definitions and Values." PTC 2 contains standards for terms, units, values of constants, and technical nomenclature. |
| 국제분류(ICS)코드 | |
| 페이지수 | 24 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASME PTC 1-2022 | General Instructions (PTC 1 - 2022) | 2022-03-31 | 표준 |
| 2 | ASME PTC 1-2015 | General Instructions (PTC 1 - 2015) | 2015-01-01 | 구판 |
| 3 | ASME PTC 1-2011 | General Instructions (PTC 1 - 2011) | 2011-01-01 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
