관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles (MFC-7M - 1987)
| 분야 | MFC : Flow Measurement |
|---|---|
| 적용범위 | This Standard applies only to the steady flow of single-phase gases and deals with devices for which direct calibration experiments have been made, sufficient in number and quantity to enable inherent systems of applications to be based on their results and coefficients to be given with certain predictable limits of uncertainty. The critical flow venturi nozzles dealt with can only be used within limits that are specified, for example nozzle throat to inlet diameter ratio and Reynolds number. This Standard specifies the geometry and method of use (installation and operating conditions) of critical flow venturi nozzles inserted in a system to determine the mass flow rate of the gas flow rate of the gas flowing through the system. It also gives necessary information for calculating the flow rate and its associated uncertainty. This Standard applies only to venturi nozzles in which the flow is critical. Critical flow exists when the mass flow rate through the venturi nozzle is the maximum possible for the existing upstream conditions. At critical flow or choked conditions, the average gas velocity at the nozzle throat closely approximates the local sonic velocity. Information is given in this Standard for cases in which: (a) the pipeline upstream of the venturi nozzle is of circular cross section; or (b) it can be assumed that there is a large space upstream of the venturi nozzle. The venturi nozzles specified in this Standard are called primary devices. Other instruments for the measurement are known as secondary devices. This Standard covers primary devices; secondary devices will be mentioned only occasionally. |
| 국제분류(ICS)코드 | |
| 페이지수 | 32 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASME MFC-7M-1987(R2014) | Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles (MFC-7M - 1987) | 1987-01-01 | 표준 |
ASME MFC-2M-1983(R2013) - Measurement Uncertainty for Fluid Flow in Closed Conduits (MFC-2M - 1983) 상세보기
ASME MFC-4M-1986(R2016) - Measurement of Gas Flow by Turbine Meters (MFC-4M - 1986) 상세보기
ASME MFC-9M-1988(R2021) - Measurement of Liquid Flow in Closed Conduits by Weighing Method (MFC-9M - 1988) 상세보기
ASME MFC-10M-2000(R2021) - Method for Establishing Installation Effects on Flow Meters (MFC-10M - 2000) 상세보기
ASME MFC-18M-2001(R2016) - Measurement of Fluid Flow using Variable Area Meters (MFC-18M - 2001) 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
