관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
| 분야 | |
|---|---|
| 적용범위 | 1.1?This specification covers the identification of polyethylene plastic pipe and fittings materials in accordance with a cell classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify manufacturing tolerances, or to determine suitability for use for a specific application. 1.1.1?Some plastic pipe and fitting PE compounds classified by this standard are sold as a base material and then combined with other material(s) (for example, color or additive concentrate) by the pipe or fitting manufacturer into a final classified compound either prior to or during production of the final article. This standard, excluding the requirements of Table 1, properties 5 and 6, and 6.1.1, can be used for property verification of the incoming base material(s) in accordance with 8.1. 1.1.2?In the case of PE compounds sold as the compound classified by the standard, see 8.1 regarding property verification of the incoming classified compound. 1.1.3?Compounds with a cell classification value other than ‘0’ for the Hydrostatic Strength Classification (property 6) rely on a defined formulation. The composition of the defined formulation can be obtained from the owner of the formulation. Note 1:?Deviations from the defined formulation may affect the Hydrostatic Strength Classification. 1.2?Polyethylene plastic materials, being thermoplastic, are reprocessable and recyclable (Note 3). This specification allows for the use of those polyethylene materials, provided that all specific requirements of this specification are met. Note 2:?The notes in this specification are for information only and shall not be considered part of this specification. Note 3:?See Guide D5033 for information and definitions related to recycled plastics. 1.3?The values stated in SI units are to be regarded as standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 4:?There is no known ISO equivalent to this standard. 1.5?For information regarding molding and extrusion materials see Specification D4976. For information regarding wire and cable materials see Specification D1248. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 9 |
| Edition | 24 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3350-24 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2024-08-01 | 표준 |
| 2 | ASTM D3350-24 REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2024-08-01 | 표준 |
| 3 | ASTM D3350-21 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2021-07-01 | 구판 |
| 4 | ASTM D3350-21 REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2021-07-01 | 구판 |
| 5 | ASTM D3350-14 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2014-11-01 | 구판 |
| 6 | ASTM D3350-14 REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2014-11-01 | 구판 |
| 7 | ASTM D3350-12e1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2012-04-01 | 구판 |
| 8 | ASTM D3350-12 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2012-04-01 | 구판 |
| 9 | ASTM D3350-10a | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2010-11-15 | 구판 |
| 10 | ASTM D3350-10 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2010-01-01 | 구판 |
| 11 | ASTM D3350-08 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2008-04-01 | 구판 |
| 12 | ASTM D3350-06 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2006-11-15 | 구판 |
| 13 | ASTM D3350-05 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2005-09-15 | 구판 |
| 14 | ASTM D3350-04 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2004-11-01 | 구판 |
| 15 | ASTM D3350-02a | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2002-08-10 | 구판 |
| 16 | ASTM D3350-01 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2002-03-10 | 구판 |
| 17 | ASTM D3350-00 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2002-03-10 | 구판 |
| 18 | ASTM D3350-02 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials | 2002-03-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
