관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | |
---|---|
적용범위 | 1.1 This practice is for general use in gathering and reporting dynamic mechanical data. It incorporates laboratory practice for determining dynamic mechanical properties of plastic specimens subjected to various oscillatory deformations on a variety of instruments of the type commonly called dynamic mechanical analyzers or dynamic thermomechanical analyzers. 1.2 This practice is intended to provide means of determining the transition temperatures, elastic, and loss moduli of plastics over a range of temperatures, frequencies, or time, by free vibration and resonant or nonresonant forced vibration techniques. Plots of elastic and loss moduli are indicative of the viscoelastic characteristics of a plastic. These moduli are functions of temperature or frequency in plastics, and change rapidly at particular temperatures or frequencies. The regions of rapid moduli change are normally referred to as transition regions. 1.3 The practice is primarily useful when conducted over a range of temperatures from −140°C to polymer softening and is valid for frequencies from 0.01 to 1000 Hz. 1.4 This practice is intended for materials that have an elastic modulus in the range from 0.5 MPa to 100 GPa (73 psi to 1.5 × 107 psi). 1.5 Discrepancies in results are known to arise when obtained under differing experimental conditions. Without changing the observed data, reporting in full (as described in this practice) the conditions under which the data were obtained will enable apparent differences observed in another study to be reconciled. An assumption of this technique is that testing is conducted in the region of linear viscoelastic behavior. 1.6 Different modes of deformation, such as tensile, bending and shear, are used, as listed in the referenced test methods. 1.7 Test data obtained by this practice are relevant and appropriate for use in engineering design. 1.8 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 8. Note 1: This practice is equivalent to ISO 6721–1. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | |
페이지수 | 8 |
Edition | 20 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D4065-20 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2020-09-01 | 표준 |
2 | ASTM D4065-20 REDLINE | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2020-09-01 | 표준 |
3 | ASTM D4065-12 REDLINE | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2012-08-01 | 구판 |
4 | ASTM D4065-12 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2012-08-01 | 구판 |
5 | ASTM D4065-06 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2006-12-01 | 구판 |
6 | ASTM D4065-95 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2001-09-10 | 구판 |
7 | ASTM D4065-01 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures | 2001-09-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기