관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
| 분야 | |
|---|---|
| 적용범위 | 1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1. Note 1: Throughout this specification the use of “ingot” in a general sense includes sow, T-bar, T-ingot, and pig. 1.2 Alloy designations are in accordance with ANSI H35.1/H35.1(M). Note 2: Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in Specifications B26/B26M, B85/B85M, B108/B108M, B618/B618M, B686/B686M, B955/B955M, and B969/B969M. 1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units. 1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1. 1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 10 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B179-18 REDLINE | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2018-05-15 | 표준 |
| 2 | ASTM B179-18 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2018-05-15 | 표준 |
| 3 | ASTM B179-17 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2017-10-01 | 구판 |
| 4 | ASTM B179-14 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2014-10-01 | 구판 |
| 5 | ASTM B179-11e1 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2011-05-01 | 구판 |
| 6 | ASTM B179-11 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2011-05-01 | 구판 |
| 7 | ASTM B179-10 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2010-05-01 | 구판 |
| 8 | ASTM B179-09 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2009-11-15 | 구판 |
| 9 | ASTM B179-06 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2006-09-01 | 구판 |
| 10 | ASTM B179-03 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 2003-04-10 | 구판 |
| 11 | ASTM B179-96 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes | 1996-12-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM B108/B108M-19 REDLINE - Standard Specification for Aluminum-Alloy Permanent Mold Castings 상세보기
DIN EN 1780-1:2003-01 - Aluminium and aluminium alloys - Designation of alloyed aluminium ingots for remelting, master alloys and castings - Part 1: Numerical designation system 상세보기
DIN EN 1780-2:2003-01 - Aluminium and aluminium alloys - Designation of alloyed aluminium ingots for remelting, master alloys and castings - Part 2: Chemical symbol based designation system 상세보기
DIN EN 1780-3:2003-01 - Aluminium and aluminium alloys - Designation of alloyed aluminium ingots for remelting, master alloys and castings - Part 3: Writing rules for chemical composition 상세보기
DIN EN 1676:2020-06 - Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
