관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
| 분야 | |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the temperature at which an arbitrary deformation occurs when specimens are subjected to an arbitrary set of testing conditions. 1.2 This test method applies to molded and sheet materials available in thicknesses of 3 mm (1/8 in.) or greater and which are rigid or semirigid at normal temperature. Note 1: Sheet stock less than 3 mm (0.125 in.) but more than 1 mm (0.040 in.) in thickness may be tested by use of a composite sample having a minimum thickness of 3 mm. The laminae must be of uniform stress distribution. One type of composite specimen has been prepared by cementing the ends of the laminae together and then smoothing the edges with sandpaper. The direction of loading shall be perpendicular to the edges of the individual laminae. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 Some older machines still use mercury-in-glass thermometers. (Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2: The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. Note 3: This standard and ISO 75-1 and ISO 75-2 address the same subject matter, but differ in technical content, and results shall not be compared between the two test methods. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 14 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D648-18 REDLINE | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2018-04-01 | 표준 |
| 2 | ASTM D648-18 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2018-04-01 | 표준 |
| 3 | ASTM D648-16 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2016-04-01 | 구판 |
| 4 | ASTM D648-07 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position (Withdrawn 2016) | 2007-03-01 | 구판 |
| 5 | ASTM D648-06 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2006-03-15 | 구판 |
| 6 | ASTM D648-04 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2004-07-01 | 구판 |
| 7 | ASTM D648-00a | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2001-08-10 | 구판 |
| 8 | ASTM D648-01 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2001-08-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D2029-97(2017) - Standard Test Methods for Water Vapor Content of Electrical Insulating Gases by Measurement of Dew Point 상세보기
ASTM D6304-16e1 - Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration 상세보기
ASTM D4294-16e1 - Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry 상세보기
ASTM D4102-82(2015) - Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers 상세보기
ASTM E1356-08(2014) - Standard Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry (Withdrawn 2023) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
