관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics
| 분야 | |
|---|---|
| 적용범위 | 1.1 This practice describes a procedure for specimen preparation and mounting when testing tapes to assess flame spread and smoke development as surface burning characteristics using Test Method E84. Tapes are to be tested in full coverage as applied to fiber cement board as described in Test Method E84. 1.2 This practice applies to tapes intended for various uses within buildings. The tapes addressed in this practice are not able to be supported by their own structural characteristics during the test. 1.3 Testing is conducted in accordance with Test Method E84. 1.4 This practice does not provide pass/fail criteria that can be used as a regulatory tool. 1.5 This practice does not apply to materials for which the test specimen does not remain in place before and during the test until maximum flame propagation has occurred. 1.6 This practice is not for system evaluation. It is for the comparison of the materials only. 1.7 Use the values stated in inch-pound units as the standard, in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details. 1.8 This fire standard cannot be used to provide quantitative measures. 1.9 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.10 This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84. See also Section 9. 1.11 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the standard. 1.12 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.13 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 2 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E2688-24 | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2024-05-01 | 표준 |
| 2 | ASTM E2688-24 REDLINE | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2024-05-01 | 표준 |
| 3 | ASTM E2688-23 | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2023-12-15 | 구판 |
| 4 | ASTM E2688-23 REDLINE | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2023-12-15 | 구판 |
| 5 | ASTM E2688-18 REDLINE | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2018-03-01 | 구판 |
| 6 | ASTM E2688-18 | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2018-03-01 | 구판 |
| 7 | ASTM E2688-16 | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2016-07-01 | 구판 |
| 8 | ASTM E2688-10 | Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics | 2010-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E2579-19 REDLINE - Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 상세보기
ASTM E2599-18 REDLINE - Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics 상세보기
ASTM E2988-17 REDLINE - Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics 상세보기
ASTM E2690-17b REDLINE - Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics 상세보기
ASTM E2404-17 REDLINE - Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) and Wood Wall or Ceiling Coverings, Facings and Veneers, to Assess Surface Burning Characteristics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
