관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality
| 분야 | ||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 This specification covers hot-wrought special quality carbon steel bars. Special quality bar applications include forging, heat treating, cold drawing, machining, and many structural uses. A guide for the selection of steel bars is contained in Practice A400. 1.2 The bars shall be furnished in the grades specified in Table 1. Sections and sizes of bar steel available are covered in Specification A29/A29M. Hot-wrought special quality carbon steel bars are produced in cut lengths and coils; the manufacturer should be consulted regarding sections and sizes available in coils, produced to a chemical composition.
(A) New designations established in accordance with Practice E527 and SAE J 1086. (B) Maximum unless otherwise indicated. (C) When silicon is required, the following ranges and limits are commonly specified: 0.10 %, max, 0.10 to 0.20 %, 0.15 to 0.35 %, or 0.20 to 0.40 %. (D) Copper can be specified when required as 0.20 % minimum. (E) When lead is required as an added element to a standard steel, a range of 0.15 to 0.35 % incl is specified. Such a steel is identified by inserting the letter “L” between the second and third numerals of the grade designation, for example, 10 L 45. A cast or heat analysis is not determinable when lead is added to the ladle stream. (F) When boron treatment is specified for killed steels, the steels can be expected to contain 0.0005 to 0.003 % boron. (G) The elements bismuth, calcium, selenium, or tellurium may be added as agreed between purchaser and supplier. (H) It is not common practice to produce these steels to specified limits for silicon because of its adverse effect on machinability. 1.3 Merchant quality hot-wrought carbon steel bars are covered in Specification A575. 1.4 Some end uses may require superior surface quality, or special chemical restrictions, metallurgical characteristics, heat treatment, or surface finishes which the purchaser may obtain by designating one or more of the available Supplementary Requirements. 1.5 The values stated in inch-pound units are to be regarded as standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
|||||||||||||||||||||||||||||||||||||||||||||||||
| 국제분류(ICS)코드 | ||||||||||||||||||||||||||||||||||||||||||||||||||
| 페이지수 | 6 | |||||||||||||||||||||||||||||||||||||||||||||||||
| Edition | 17 | |||||||||||||||||||||||||||||||||||||||||||||||||
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A576-23 | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2023-11-01 | 표준 |
| 2 | ASTM A576-23 REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2023-11-01 | 표준 |
| 3 | ASTM A576-17 REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2017-11-01 | 구판 |
| 4 | ASTM A576-17 | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2017-11-01 | 구판 |
| 5 | ASTM A576-90b(2012) | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2012-03-01 | 구판 |
| 6 | ASTM A576-90b(2006) | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2006-03-01 | 구판 |
| 7 | ASTM A576-90b(2000) | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality | 2000-01-01 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
