관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 10.04 : 전자 |
---|---|
적용범위 | 1.1?This practice provides two NDT inspection levels, with acceptance criteria and applicable NDT method(s). It is not based on part driven engineering criteria but the practical inspection capability of properly applied NDT methods.2 Flaw detection is based on the flaw’s characteristic and relative orientation to the applied NDT method. 1.2?Applicability?This standard applies to parts that are processed using laser beam powder bed fusion (PBF-LB). Post processing of PBF-LB parts by hot isostatic pressing (HIP) can close (partially or completely) certain types of defects. NDT techniques applied to HIP’ed parts may not detect collapsed defects. It is the responsibility of the user of this standard to determine if this condition is rejectable and what NDT technique to use. 1.3?There are areas in this practice that may require agreement between the cognizant engineering organization and the additive manufacturing supplier, or specific direction from the cognizant engineering organization. 1.4?Units?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | |
페이지수 | 5 |
Edition | 24 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM F3704/F3704M-24 | Standard Practice for Nondestructive Testing (NDT), Inspection Levels and Acceptance Criteria for Parts Manufactured with Laser Based Powder Fusion | 2024-10-01 | 표준 |
관련상품이 존재하지 않습니다.
ASTM E10-23 - Standard Test Method for Brinell Hardness of Metallic Materials 상세보기
ASTM E92-23 - Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 상세보기
ASTM F3637-23 - Standard Guide for Additive Manufacturing of Metal ? Finished Part Properties ? Methods for Relative Density Measurement 상세보기
ASTM F2808-23 - Standard Test Method for Performing Behind-the-Knee (BTK) Test for Evaluating Skin Irritation Response to Products and Materials That Come Into Repeated or Extended Contact with Skin 상세보기
ASTM F3624-23 - Standard Guide for Additive Manufacturing of Metals ? Powder Bed Fusion ? Measurement and Characterization of Surface Texture 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기