관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys
| 분야 | 02.01 : 동 및 동합금 |
|---|---|
| 적용범위 | 1.1?This test method describes a procedure to determine the presence of residual stresses in wrought copper alloy products that may lead to stress corrosion cracking. An ammonia vapor atmosphere is used as an accelerated test. 1.2?This test method is only suitable for products fabricated from copper alloys that are known to be susceptible to stress corrosion cracking in ammonia vapor atmospheres. It is intended to create an environmental condition of reproducible severity. Note 1:?It is well known that the critical step in the cracking mechanism is the development of an environment in the condensate film that occurs on the surface of the test specimen, and is rich in copper complex ions. 1.3?The severity of this test method depends upon the pH of the corrosive solution. In Annex A1 are given four different atmospheres to which the product may be exposed, and the appropriate pH of the solution to be used for the test, depending on the risk level associated with the intended application. 1.3.1?The appropriate pH value for the test shall be specified in the product specification, or as per established agreement between the supplier and purchaser, with respect to the alloy and its intended application. 1.4?Units?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.120.30 : 구리 및 구리합금 |
| 페이지수 | 4 |
| Edition | 06(2024) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B858-06(2024) | Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys | 2024-07-01 | 표준 |
| 2 | ASTM B858-06(2018) | Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys | 2018-03-01 | 구판 |
| 3 | ASTM B858-06(2012) | Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys | 2012-04-01 | 구판 |
| 4 | ASTM B858-06 | Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys | 2006-03-15 | 구판 |
| 5 | ASTM B858-95 | Standard Test Method for Ammonia Vapor Test for Determination Susceptibility to Stress Corrosion Cracking in Copper Alloys | 2001-10-10 | 구판 |
| 6 | ASTM B858-01 | Standard Test Method for Ammonia Vapor Test for Determination Susceptibility to Stress Corrosion Cracking in Copper Alloys | 2001-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ISO 6957:1988 - Copper alloys — Ammonia test for stress corrosion resistance 상세보기
DIN EN ISO 5771:2024-09 - Rubber hoses and hose assemblies for transferring anhydrous ammonia - Specification (ISO 5771:2024) 상세보기
DIN 50916-2:2023-07 - Testing of copper alloys - Stress corrosion cracking test using ammonia - Part 2: Testing of components 상세보기
DIN 50916-1:2023-07 - Testing of copper alloys - Stress corrosion cracking test in ammonia - Part 1: Testing of tubes, rods and profiles 상세보기
AS/NZS 2022:2003 - Anhydrous ammonia - Storage and handling 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
