관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method
| 분야 | 03.03 : 비 파괴검사 (Ⅰ) |
|---|---|
| 적용범위 | 1.1?This test method covers a procedure for determining the electrical conductivity of nonmagnetic materials, typically nonmagnetic metals, using the electromagnetic (eddy current) method. The procedure has been written primarily for use with commercially available direct reading electrical conductivity instruments. General purpose eddy current instruments may also be used for electrical conductivity measurements but will not be addressed in this test method. 1.2?This test method is applicable to nonmagnetic materials that have either a flat or slightly curved surface and includes metals with or without a thin nonconductive coating. 1.3?Eddy current determinations of electrical conductivity may be used in the sorting of nonmagnetic materials with respect to variables such as type of alloy, aging, cold deformation, heat treatment, effects associated with non-uniform heating or overheating, and effects of corrosion. The usefulness of the examinations of these properties is dependent on the amount of electrical conductivity change caused by a change in the specific variable. 1.4?Electrical conductivity, when evaluated with eddy current instruments, is usually expressed as a percentage of the conductivity of the International Annealed Copper Standard (%?IACS) or Siemens/meter (S/m). The conductivity of the Annealed Copper Standard is defined to be 0.58? ×?108 S/m (100?%?IACS) at 20?°C. 1.5?The values stated in SI units are regarded as standard. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 17.220.20 : 전기 및 자기량 측정 |
| 페이지수 | 6 |
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E1004-23 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method | 2023-12-01 | 표준 |
| 2 | ASTM E1004-23 REDLINE | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method | 2023-12-01 | 표준 |
| 3 | ASTM E1004-17 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method | 2017-06-01 | 구판 |
| 4 | ASTM E1004-17 REDLINE | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method | 2017-06-01 | 구판 |
| 5 | ASTM E1004-09 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method | 2009-05-15 | 구판 |
| 6 | ASTM E1004-02 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method | 2002-07-10 | 구판 |
| 7 | ASTM E1004-99 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method | 1999-08-10 | 구판 |
관련상품이 존재하지 않습니다.
SAE AMS4341H - Aluminum Alloy, Extrusions, 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T73511), Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged 상세보기
SAE AMS4337C - Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged 상세보기
SAE AMS4121K - Aluminum Alloy Bars, Rods, and Wire, Rolled, Drawn, or Cold Finished 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6, -T651) Solution and Precipitation Heat Treated 상세보기
ASTM E1316-24 - Standard Terminology for Nondestructive Examinations 상세보기
ASTM G34-23 - Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
