관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Magnetic Particle Examination of Steel Forgings
| 분야 | 01.05 : 철강-환봉, 단조품, 베어링, 체인, 스프링 |
|---|---|
| 적용범위 | 1.1?This practice2 covers a procedure for magnetic particle examination of steel forgings. The procedure will produce consistent results upon which acceptance standards can be based. This practice does not contain acceptance standards or recommended quality levels. 1.2?Only direct current or rectified alternating (full or half wave) current shall be used as the electric power source for any of the magnetizing methods. Alternating current is not permitted because its capability to detect subsurface discontinuities is very limited and therefore unsuitable. 1.2.1?Portable battery powered electromagnetic yokes are outside the scope of this practice. Note 1:?Guide E709 may be utilized for magnetic particle examination in the field for machinery components originally manufactured from steel forgings. 1.3?The minimum requirements for magnetic particle examination shall conform to practice standards of Practice E1444/E1444M. If the requirements of this practice are in conflict with the requirements of Practice E1444/E1444M, the requirements of this practice shall prevail. 1.4?This practice and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units. 1.5?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 |
77.040.20 : 금속의 비파괴 시험
77.140.85 : 철강 단조 |
| 페이지수 | 8 |
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A275/A275M-23 | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2023-11-01 | 표준 |
| 2 | ASTM A275/A275M-23 REDLINE | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2023-11-01 | 표준 |
| 3 | ASTM A275/A275M-18(2023) | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2023-03-01 | 구판 |
| 4 | ASTM A275/A275M-18 | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2018-05-01 | 구판 |
| 5 | ASTM A275/A275M-18 REDLINE | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2018-05-01 | 구판 |
| 6 | ASTM A275/A275M-15 | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2015-05-01 | 구판 |
| 7 | ASTM A275/A275M-08(2013) | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2013-04-01 | 구판 |
| 8 | ASTM A275/A275M-08 | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2008-11-01 | 구판 |
| 9 | ASTM A275/A275M-07 | Standard Practice for Magnetic Particle Examination of Steel Forgings | 2007-09-01 | 구판 |
| 10 | ASTM A275/A275M-06 | Standard Test Method for Magnetic Particle Examination of Steel Forgings | 2006-05-01 | 구판 |
| 11 | ASTM A275/A275M-98(2003) | Standard Test Method for Magnetic Particle Examination of Steel Forgings | 2003-04-10 | 구판 |
| 12 | ASTM A275/A275M-98 | Standard Test Method for Magnetic Particle Examination of Steel Forgings | 1998-09-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM A388/A388M-23 - Standard Practice for Ultrasonic Examination of Steel Forgings 상세보기
ASTM A105/A105M-23 - Standard Specification for Carbon Steel Forgings for Piping Applications 상세보기
ASTM A961/A961M-23 - Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications 상세보기
ASTM A153/A153M-23 - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware 상세보기
ASTM A350/A350M-23 - Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
