관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
| 분야 | 04.13 : 토목 합성 자재 |
|---|---|
| 적용범위 | 1.1?This test method covers the determination of the tensile strength properties of geogrids by subjecting strips of varying width to tensile loading. 1.2?Three alternative procedures are provided to determine the tensile strength, as follows: 1.2.1?Method A?Testing a single geogrid rib in tension (N or lbf). 1.2.2?Method B?Testing multiple geogrid ribs in tension (kN/m or lbf/ft). 1.2.3?Method C?Testing multiple layers of multiple geogrid ribs in tension (kN/m or lbf/ft). 1.3?This test method is intended for quality control and conformance testing of geogrids. 1.4?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 59.080.70 : 지오섬유 |
| 페이지수 | 6 |
| Edition | 15(2023) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D6637/D6637M-15(2023) | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method | 2023-11-15 | 표준 |
| 2 | ASTM D6637/D6637M-15 REDLINE | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method | 2015-07-15 | 구판 |
| 3 | ASTM D6637/D6637M-15 | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method | 2015-07-15 | 구판 |
관련상품이 존재하지 않습니다.
KS F 2400 - 콘크리트 타설 일체 부착형 자착식 시트 방수재 시험방법 상세보기
ASTM C494/C494M-24 - Standard Specification for Chemical Admixtures for Concrete 상세보기
ASTM D545-23 - Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types) 상세보기
ASTM D5322-23 - Standard Practice for Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids 상세보기
ASTM D1200-23 - Standard Test Method for Viscosity by Ford Viscosity Cup 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
