관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for General Requirements for Alloy and Stainless Steel Pipe
| 분야 | 01.01 : 철강-배관, 튜브, 관이음쇠 | ||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1?This specification2 covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below. 1.2?In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.
1.3?The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units apply unless the “M” designation (SI) of the product specification is specified in the order. Note 1:?The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as “nominal diameter,” “size,” “nominal bore,” and “nominal size.” 1.4?The following precautionary statement pertains only to the test method portion, Section 21, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||
| 국제분류(ICS)코드 | 23.040.10 : 주철 및 강 파이프 | ||||||||||||||||||||||||||||||||||||||||||
| 페이지수 | 12 | ||||||||||||||||||||||||||||||||||||||||||
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A999/A999M-23 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2023-09-01 | 표준 |
| 2 | ASTM A999/A999M-18 REDLINE | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2018-03-01 | 구판 |
| 3 | ASTM A999/A999M-17 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2017-09-01 | 구판 |
| 4 | ASTM A999/A999M-16 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2016-09-01 | 구판 |
| 5 | ASTM A999/A999M-15 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2015-12-01 | 구판 |
| 6 | ASTM A999/A999M-14 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2014-03-01 | 구판 |
| 7 | ASTM A999/A999M-13 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2013-04-01 | 구판 |
| 8 | ASTM A999/A999M-12 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2012-05-01 | 구판 |
| 9 | ASTM A999/A999M-11 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2011-05-15 | 구판 |
| 10 | ASTM A999/A999M-04a(2009) | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2009-10-01 | 구판 |
| 11 | ASTM A999/A999M-04a | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2004-07-01 | 구판 |
| 12 | ASTM A999/A999M-04 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2004-05-01 | 구판 |
| 13 | ASTM A999/A999M-98 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2001-03-10 | 구판 |
| 14 | ASTM A999/A999M-01 | Standard Specification for General Requirements for Alloy and Stainless Steel Pipe | 2001-03-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E1181-02(2023) - Standard Test Methods for Characterizing Duplex Grain Sizes 상세보기
ASTM E45-18a(2023) - Standard Test Methods for Determining the Inclusion Content of Steel 상세보기
ISO 5173:2023 - Destructive tests on welds in metallic materials — Bend tests 상세보기
ISO 643:2024 - Steels — Micrographic determination of the apparent grain size 상세보기
ISO 6507-1:2023 - Metallic materials — Vickers hardness test — Part 1: Test method 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
