관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Compressive Properties of Rigid Plastics
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1?This test method covers the determination of the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading. Test specimens of standard shape are employed. This procedure is applicable for a composite modulus up to and including 41,370 MPa (6,000,000 psi). 1.2?The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. Note 1:?For compressive properties of resin-matrix composites reinforced with oriented continuous, discontinuous, or cross-ply reinforcements, tests may be made in accordance with Test Method D3410/D3410M or D6641/D6641M. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 13.1. Note 2:?This standard is equivalent to ISO?604. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 8 |
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D695-23 | Standard Test Method for Compressive Properties of Rigid Plastics | 2023-08-01 | 표준 |
| 2 | ASTM D695-23 REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics | 2023-08-01 | 표준 |
| 3 | ASTM D695-15 | Standard Test Method for Compressive Properties of Rigid Plastics | 2015-09-01 | 구판 |
| 4 | ASTM D695-15 REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics | 2015-09-01 | 구판 |
| 5 | ASTM D695-10 | Standard Test Method for Compressive Properties of Rigid Plastics | 2010-04-01 | 구판 |
| 6 | ASTM D695-08 | Standard Test Method for Compressive Properties of Rigid Plastics | 2008-08-01 | 구판 |
| 7 | ASTM D695-02a | Standard Test Method for Compressive Properties of Rigid Plastics | 2002-08-10 | 구판 |
| 8 | ASTM D695-96 | Standard Test Method for Compressive Properties of Rigid Plastics | 2002-04-10 | 구판 |
| 9 | ASTM D695-02 | Standard Test Method for Compressive Properties of Rigid Plastics | 2002-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D2583-13a - Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) 상세보기
ASTM D2651-01(2016) - Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding 상세보기
ASTM B26/B26M-18e1 - Standard Specification for Aluminum-Alloy Sand Castings 상세보기
ASTM B85/B85M-18e1 - Standard Specification for Aluminum-Alloy Die Castings 상세보기
ASTM C1048-18 - Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
