관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Bridge Impact Testing
| 분야 | 15.10 : 포장 |
|---|---|
| 적용범위 | 1.1?This test method is intended to determine the capability of a long package with a narrow cross-section to resist impact near its center when the package is supported only at its ends. This test method allows the user to select from two test options: Option A employs the use of a free-fall drop tester (see Exhibit B), and Option B employs the use of simulated mechanical impact testing equipment (S.M.I.T.E.; see Exhibit A). The two optional procedures are designed to impart the same amount of kinetic energy at impact; therefore, each procedure yields equal damage-producing potential. 1.2?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 97.150 : 비바닥재 섬유 |
| 페이지수 | 5 |
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D5265-23 | Standard Test Method for Bridge Impact Testing | 2023-03-15 | 표준 |
| 2 | ASTM D5265-23 REDLINE | Standard Test Method for Bridge Impact Testing | 2023-03-15 | 표준 |
| 3 | ASTM D5265-09(2016) | Standard Test Method for Bridge Impact Testing | 2016-06-01 | 구판 |
| 4 | ASTM D5265-09 | Standard Test Method for Bridge Impact Testing | 2009-11-01 | 구판 |
| 5 | ASTM D5265-03(2009) | Standard Test Method for Bridge Impact Testing | 2009-03-01 | 구판 |
| 6 | ASTM D5265-03 | Standard Test Method for Bridge Impact Testing | 2003-10-01 | 구판 |
| 7 | ASTM D5265-92(1998)e1 | Standard Test Method for Bridge Impact Testing | 1998-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D6179-20 - Standard Test Methods for Rough Handling of Unitized Loads and Large Shipping Cases and Crates 상세보기
ASTM D642-20 - Standard Test Method for Determining Compressive Resistance of Shipping Containers, Components, and Unit Loads 상세보기
ASTM D4332-22 - Standard Practice for Conditioning Containers, Packages, or Packaging Components for Testing 상세보기
ASTM D5277-22 - Standard Test Method for Performing Programmed Horizontal Impacts Using an Inclined Impact Tester 상세보기
ASTM D5276-19(2023) - Standard Test Method for Drop Test of Loaded Containers by Free Fall 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
