관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys
| 분야 | 03.02 : 마모 및 침식;금속 부식 |
|---|---|
| 적용범위 | 1.1?These test methods cover two tests as follows: 1.1.1?Method A, Ferric Sulfate-Sulfuric Acid Test (Sections 3 ? 10, inclusive)?This test method describes the procedure for conducting the boiling ferric sulfate?50?% sulfuric acid test which measures the susceptibility of certain nickel-rich, chromium-bearing alloys to intergranular corrosion (see Terminology G193), which may be encountered in certain service environments. The uniform corrosion rate obtained by this test method, which is a function of minor variations in alloy composition, may easily mask the intergranular corrosion components of the overall corrosion rate on alloys N10276, N06022, N06059, and N06455. 1.1.2?Method B, Mixed Acid-Oxidizing Salt Test (Sections 11 ? 18, inclusive)?This test method describes the procedure for conducting a boiling 23?% sulfuric?+?1.2?% hydrochloric?+?1?% ferric chloride?+?1?% cupric chloride test which measures the susceptibility of certain nickel-rich, chromium-bearing alloys to display a step function increase in corrosion rate when there are high levels of grain boundary precipitation. 1.2?The purpose of these two test methods is to detect susceptibility to intergranular corrosion as influenced by variations in processing or composition, or both. Materials shown to be susceptible may or may not be intergranularly corroded in other environments. This must be established independently by specific tests or by service experience. 1.3?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1?Exception?Some desired corrosion rate units in 8.1.1 are given in inch-pound units. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning statements are given in 5.1.1, 5.1.3, 5.1.9, 13.1.1, and 13.1.11. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.120.40 : 니켈, 크로뮴 및 합금 |
| 페이지수 | 7 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G28-22 | Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys | 2022-12-01 | 표준 |
| 2 | ASTM G28-22 REDLINE | Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys | 2022-12-01 | 표준 |
| 3 | ASTM G28-02(2015) | Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys | 2015-11-01 | 구판 |
| 4 | ASTM G28-02(2008) | Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys | 2008-05-01 | 구판 |
| 5 | ASTM G28-02 | Standard Test Methods of Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys | 2002-10-10 | 구판 |
| 6 | ASTM G28-97 | Standard Test Methods of Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys | 1997-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E562-19e1 - Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count 상세보기
ASTM A923-23 - Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels 상세보기
ASTM E92-23 - Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 상세보기
ASTM E10-23 - Standard Test Method for Brinell Hardness of Metallic Materials 상세보기
ASTM A370-23 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
