관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
---|---|
적용범위 | 1.1?This test method covers determination of the microindentation hardness of materials. 1.2?This test method covers microindentation tests made with Knoop and Vickers indenters under test forces in the range from 9.8 × 10-3 to 9.8 N (1 to 1000 gf). 1.3?This test method includes an analysis of the possible sources of errors that can occur during microindentation testing and how these factors affect the precision, bias, repeatability, and reproducibility of test results. 1.4?Information pertaining to the requirements for direct verification and calibration of the testing machine and the requirements for the manufacture and calibration of Vickers and Knoop reference hardness test blocks are in Test Method E92. Note 1:?While Committee E04 is primarily concerned with metals, the test procedures described are applicable to other materials. 1.5?Units?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 19.060 : 기계 시험과 기구 |
페이지수 | 40 |
Edition | 22 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM E384-22 | Standard Test Method for Microindentation Hardness of Materials | 2022-10-01 | 표준 |
2 | ASTM E384-22 REDLINE | Standard Test Method for Microindentation Hardness of Materials | 2022-10-01 | 표준 |
3 | ASTM E384-17 | Standard Test Method for Microindentation Hardness of Materials | 2017-06-01 | 구판 |
4 | ASTM E384-17 REDLINE | Standard Test Method for Microindentation Hardness of Materials | 2017-06-01 | 구판 |
5 | ASTM E384-16 | Standard Test Method for Microindentation Hardness of Materials | 2016-02-01 | 구판 |
6 | ASTM E384-11e1 | Standard Test Method for Knoop and Vickers Hardness of Materials | 2011-08-01 | 구판 |
7 | ASTM E384-11 | Standard Test Method for Knoop and Vickers Hardness of Materials | 2011-08-01 | 구판 |
8 | ASTM E384-10e2 | Standard Test Method for Knoop and Vickers Hardness of Materials | 2010-02-01 | 구판 |
9 | ASTM E384-10e1 | Standard Test Method for Knoop and Vickers Hardness of Materials | 2010-02-01 | 구판 |
10 | ASTM E384-10 | Standard Test Method for Microindentation Hardness of Materials | 2010-02-01 | 구판 |
11 | ASTM E384-09 | Standard Test Method for Microindentation Hardness of Materials | 2009-05-01 | 구판 |
12 | ASTM E384-08ae1 | Standard Test Method for Microindentation Hardness of Materials | 2008-03-15 | 구판 |
13 | ASTM E384-08a | Standard Test Method for Microindentation Hardness of Materials | 2008-03-15 | 구판 |
14 | ASTM E384-08 | Standard Test Method for Microindentation Hardness of Materials | 2008-01-01 | 구판 |
15 | ASTM E384-07a | Standard Test Method for Microindentation Hardness of Materials | 2007-12-15 | 구판 |
16 | ASTM E384-07 | Standard Test Method for Microindentation Hardness of Materials | 2007-07-01 | 구판 |
17 | ASTM E384-06 | Standard Test Method for Microindentation Hardness of Materials | 2006-11-15 | 구판 |
18 | ASTM E384-05a | Standard Test Method for Microindentation Hardness of Materials | 2005-08-15 | 구판 |
19 | ASTM E384-05 | Standard Test Method for Microindentation Hardness of Materials | 2005-07-01 | 구판 |
20 | ASTM E384-99 | Standard Test Method for Microindentation Hardness of Materials | 1999-11-10 | 구판 |
21 | ASTM E384-99e1 | Standard Test Method for Microindentation Hardness of Materials | 1999-11-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E10-23 - Standard Test Method for Brinell Hardness of Metallic Materials 상세보기
ASTM E10-18 - Standard Test Method for Brinell Hardness of Metallic Materials 상세보기
ASTM E8/E8M-22 - Standard Test Methods for Tension Testing of Metallic Materials 상세보기
ASTM E1820-22e1 - Standard Test Method for Measurement of Fracture Toughness 상세보기
ASTM A370-22 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기