관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Guide for Gamma Radiation Shielding Performance Testing
| 분야 | 12.01 : 원자력 에너지 (Ⅰ) |
|---|---|
| 적용범위 | 1.1?This guide identifies appropriate test methods for determining the sufficiency of radiological shielding for hot cells and shielded enclosures. 1.2?After constructing or modifying radiological shielding, it is necessary to verify that shielding performance meets or exceeds the shielding performance requirements. This is typically accomplished using sealed test sources of much less activity than the design basis. This allows for modifications or correction of any discrepancies identified before the commissioning of the hot cell. 1.3?The guidance and practices recommended by this guide are applicable to both new and existing shielded facilities and enclosures for evaluating shielding suitability and locating the existence of shine paths or other shielding anomalies that result from design, manufacture, or construction. 1.4?Two types of testing may be performed. 1.4.1?Shielding performance verification testing provides evidence that the shielding configuration is sufficient for meeting established performance criteria and for identifying deficiencies in the shielding configuration or components that may not have been addressed during design. Test results are expected to demonstrate that shielding performance meets or exceeds design criteria, not match the dose rates predicted analytically. 1.4.2?Shielding performance verification testing identifies shielding deficiencies (hot spots) in the installed configuration relative to adjacent shielding but does not demonstrate compliance with any quantitative shielding performance requirement. 1.5?Performance testing should be specified and performed to assess shielding adequacy with sources in all critical locations. 1.6?Requirements for shielding performance testing should be clearly defined in design basis or procurement documentation. 1.7?This guide is not applicable to neutron radiation shielding performance evaluations. 1.8?Units?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.8.1?Units for total activity should be given in Becquerel (Bq) or curies (Ci). 1.8.2?Units for dose rate as measured during testing should be given in Sieverts (Sv/h) or rad/h. 1.8.3?Distances and locations should be provided in centimetres or inches. 1.9?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 13.280 : 방사능 보호 |
| 페이지수 | 5 |
| Edition | 17(2022) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C1831/C1831M-17(2022) | Standard Guide for Gamma Radiation Shielding Performance Testing | 2022-07-01 | 표준 |
| 2 | ASTM C1831/C1831M-17 | Standard Guide for Gamma Radiation Shielding Performance Testing | 2017-11-01 | 구판 |
관련상품이 존재하지 않습니다.
ISO 11451-5:2023 - Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 5: Reverberation chamber 상세보기
ASTM F3057-21 - Standard Test Method for Electromagnetic Shielding Effectiveness of Glazings 상세보기
ASTM D2520-21 - Standard Test Methods for Complex Permittivity (Dielectric Constant) of Solid Electrical Insulating Materials at Microwave Frequencies and Temperatures to 1650?°C 상세보기
ASTM E1851-21 - Standard Test Method for Electromagnetic Shielding Effectiveness of Durable Rigid Wall Relocatable Structures 상세보기
ASTM D3380-22 - Standard Test Method for Relative Permittivity (Dielectric Constant) and Dissipation Factor of Polymer-Based Microwave Circuit Substrates 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
