관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
| 분야 | 02.02 : 알루미늄 및 마그네슘 합금 |
|---|---|
| 적용범위 | 1.1?This specification2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2, 3, 4, and 5, and in the following finishes: 1.1.1?Plate in all alloys and sheet in heat-treatable alloys: mill finish. 1.1.2?Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish. 1.2?Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. Note 1:?Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2:?See Specification B632/B632M for tread plate. Note 3:?See Specification B928/B928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3?% or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in this specification, which do not require the additional corrosion testing/capability called out in Specification B928/B928M, may be suitable for marine and similar environment applications. 1.3?For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.150.10 : 알루미늄 제품 |
| 페이지수 | 42 |
| Edition | 21a |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B209/B209M-21a | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2021-12-01 | 표준 |
| 2 | ASTM B209/B209M-21a REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2021-12-01 | 표준 |
| 3 | ASTM B209/B209M-21 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2021-05-01 | 구판 |
| 4 | ASTM B209/B209M-21 REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2021-05-01 | 구판 |
관련상품이 존재하지 않습니다.
ASME B16.47-2020 - Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch Standard 상세보기
ASME B16.5-2020 - Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard 상세보기
ASTM D2996-17 - Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe 상세보기
ASTM D4161-14(2019) - Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals 상세보기
ASTM D3517-19 - Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
