상세정보

분야	15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물
적용범위	1.1?This test method describes the determination of the opening mode-I interlaminar fracture toughness, GIc, of unidirectional fiber-reinforced polymer matrix composite laminates using the double cantilever beam (DCB) specimen (Fig. 1). FIG. 1?Double Cantilever Beam Specimen 1.2?This test method is limited to use with composites consisting of unidirectional carbon-fiber and glass-fiber-reinforced laminates with brittle or tough single-phase polymer matrices. This limited scope reflects the experience gained in round-robin testing. This test method may prove useful for other types and classes of composite materials; however, certain interferences have been noted (see 6.6). 1.3?Units?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3.1?Within the text, the inch-pound units are shown in brackets. 1.4?This standard may involve hazardous materials, operations, and equipment. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드	83.120 : 강화 플라스틱
페이지수	14
Edition	21

이력정보

• 관련상품

  관련상품이 존재하지 않습니다.

• 다른 사람이 함께 구입한 상품

  ASTM D6671/D6671M-22 - Standard Test Method for Mixed Mode I-Mode II Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composites 상세보기

  ASTM D7248/D7248M-21 - Standard Test Method for High Bearing - Low Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens 상세보기

  ASTM D6641/D6641M-16e2 - Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture 상세보기

  ASTM D5379/D5379M-19e1 - Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method 상세보기

  ASTM D3410/D3410M-16e1 - Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading 상세보기

• 추천 상품

  IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기

  IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기

  KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기

  KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기

  KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기