관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles
| 분야 | 01.06 : 피복 철강 제품 |
|---|---|
| 적용범위 | 1.1?This test method covers procedures for determining the weight [mass] of coating on aluminum-coated iron or steel sheets and wire, and on other aluminum-coated iron and steel articles. 1.2?Units?The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3?For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see Note 1. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 25.220.40 : 금속 도장 |
| 페이지수 | 6 |
| Edition | 21 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A428/A428M-21 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2021-05-01 | 표준 |
| 2 | ASTM A428/A428M-21 REDLINE | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2021-05-01 | 표준 |
| 3 | ASTM A428/A428M-10(2019) | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2019-05-01 | 구판 |
| 4 | ASTM A428/A428M-10(2014) | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2014-08-01 | 구판 |
| 5 | ASTM A428/A428M-10 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2010-05-01 | 구판 |
| 6 | ASTM A428/A428M-06 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2006-11-01 | 구판 |
| 7 | ASTM A428/A428M-95 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2001-04-10 | 구판 |
| 8 | ASTM A428/A428M-01 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2001-04-10 | 구판 |
관련상품이 존재하지 않습니다.
SAE J1681_200001 - Gasoline, Alcohol, and Diesel Fuel Surrogates for Materials Testing 상세보기
JIS A 5525:2019 - Steel pipe piles 상세보기
JIS R 1688:2010 - Methods for chemical analysis of magnesium oxide powders for fine ceramics 상세보기
ASTM E1077-14(2021) - Standard Test Methods for Estimating the Depth of Decarburization of Steel Specimens 상세보기
ASTM D610-08(2019) - Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
