관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
| 분야 | 02.04 : 비철금속-니켈, 납, 주석, 귀금속, 일차금속 등 |
|---|---|
| 적용범위 | 1.1?This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N07725, UNS N07740, UNS N09945, UNS N09925, UNS N07718, UNS N10276, UNS N06985)2 as shown in Table 1. 1.2?Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plus precipitation hardened and descaled conditions. When atmosphere control is used, descaling is not necessary. 1.3?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 23.040.15 : 비철금속 파이프 |
| 페이지수 | 5 |
| Edition | 21 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B983-21 | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2021-04-01 | 표준 |
| 2 | ASTM B983-21 REDLINE | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2021-04-01 | 표준 |
| 3 | ASTM B983-16e1 | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2016-10-01 | 구판 |
| 4 | ASTM B983-16 | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2016-10-01 | 구판 |
| 5 | ASTM B983-15 | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2015-10-01 | 구판 |
| 6 | ASTM B983-13a | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2013-10-01 | 구판 |
| 7 | ASTM B983-13 | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2013-02-01 | 구판 |
| 8 | ASTM B983-12 | Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube | 2012-05-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E562-19 - Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count 상세보기
ASTM B381-13(2019) - Standard Specification for Titanium and Titanium Alloy Forgings 상세보기
ASTM E18-19 - Standard Test Methods for Rockwell Hardness of Metallic Materials 상세보기
ASTM B299/B299M-18 - Standard Specification for Titanium Sponge 상세보기
ASTM A450/A450M-18a - Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
