관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading
| 분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
|---|---|
| 적용범위 | 1.1?This standard describes three test methods2 for determining the modulus of elasticity in bending, the bending proof strength, and the offset yield strength in bending of metallic strips or sheets intended for the use in flat springs: 1.1.1?Test Method A?a cantilever beam test, 1.1.2?Test Method B?a three-point beam test (that is, a beam resting on two supports and centrally loaded), and 1.1.3?Test Method C?a four-point beam test (that is, a beam resting on two supports and loaded at two points equally spaced from each support). 1.2?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 21.160 : 스프링 |
| 페이지수 | 9 |
| Edition | 21 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E855-21 | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading | 2021-02-01 | 표준 |
| 2 | ASTM E855-21 REDLINE | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading | 2021-02-01 | 표준 |
| 3 | ASTM E855-08(2013) | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading | 2013-04-01 | 구판 |
| 4 | ASTM E855-08 | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading | 2008-12-01 | 구판 |
| 5 | ASTM E855-90(1995) | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading | 2000-01-01 | 구판 |
| 6 | ASTM E855-90(2000) | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading | 2000-01-01 | 구판 |
관련상품이 존재하지 않습니다.
KS Q ISO 31000 - 리스크관리 — 가이드라인 상세보기
ASTM E317-21 - Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments 상세보기
ASTM A255-20a - Standard Test Methods for Determining Hardenability of Steel 상세보기
ASTM E2310-04(2015) - Standard Guide for Use of Spectral Searching by Curve Matching Algorithms with Data Recorded Using Mid-Infrared Spectroscopy (Withdrawn 2024) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
