관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Guide for Laboratory Immersion Corrosion Testing of Metals
| 분야 | 03.02 : 마모 및 침식;금속 부식 |
|---|---|
| 적용범위 | 1.1?This guide covers and describes the factors that influence laboratory immersion corrosion tests, particularly mass loss tests. These factors include apparatus, sampling, test specimen, test conditions (test solution composition, temperature, gas sparging, fluid motion, solution volume, method of supporting test specimens, duration of test), methods of cleaning test specimens, interpretation of results, and calculation of corrosion rates. This guide also emphasizes the importance of recording all pertinent data and provides a checklist for reporting test data. 1.2?The specific evaluation of localized attack, environmentally assisted cracking, and effects of solution flow are not within the scope of this guide. 1.3?This guide is intended to be used by those designing laboratory immersion tests who may not be familiar with all of the variables to consider and the pitfalls that could be encountered when designing and conducting this kind of testing. It should be used as a reference to ensure that the test will allow generation of data relevant to the application with the minimum of interferences. 1.4?The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.060 : 금속 부식 |
| 페이지수 | 10 |
| Edition | 21 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G31-21 | Standard Guide for Laboratory Immersion Corrosion Testing of Metals | 2021-01-01 | 표준 |
| 2 | ASTM G31-21 REDLINE | Standard Guide for Laboratory Immersion Corrosion Testing of Metals | 2021-01-01 | 표준 |
| 3 | ASTM G31-72(2004) | Standard Practice for Laboratory Immersion Corrosion Testing of Metals | 2004-05-01 | 구판 |
| 4 | ASTM G31-72(1999) | Standard Practice for Laboratory Immersion Corrosion Testing of Metals | 1999-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM G3-14(2019) - Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing 상세보기
ASTM G4-01(2014) - Standard Guide for Conducting Corrosion Tests in Field Applications (Withdrawn 2023) 상세보기
ASTM E2809-13 - Standard Guide for Using Scanning Electron Microscopy/X-Ray Spectrometry in Forensic Paint Examinations 상세보기
NACE AMPP SP0403 , September 9, 2023 - Avoiding Caustic Stress Corrosion Cracking of Refinery Equipment and Piping 상세보기
NACE AMPP TM0316 , August 9, 2023 - Four-Point Bend Testing of Materials for Oil and Gas Applications 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
