관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Permeability of Weakly Magnetic Materials
| 분야 | 03.07 : 자기적 특성 |
|---|---|
| 적용범위 | 1.1?These test methods cover four procedures for determination of the permeability [relative permeability]2 of materials having a relative permeability not exceeding 6.0. 1.2?The test methods covered are as follows: 1.2.1?Test Method 1?Fluxmetric Method is suitable for materials with relative permeabilities between 1.0 and 4.0. This method permits the user to select the magnetic field strength at which the permeability is to be measured. 1.2.2?Test Method 2?Permeability of Paramagnetic Materials has been eliminated as an acceptable method of test. 1.2.3?Test Method 3?Low Mu Permeability Indicator is suitable for measuring the permeability of a material as “less than” or “greater than” that of calibrated standard inserts with relative permeabilities between 1.01 and 6.0, as designated for use in a Low-Mu Permeability Indicator.3 In this method, a small volume of specimen is subjected to a local magnetic field that varies in magnitude and direction, so it is not possible to specify the magnetic field strength at which the measurement is made. 1.2.4?Test Method 4?Flux Distortion is suitable for materials with relative permeabilities between 1.0 and 2.0. In this method, a small volume of specimen is subjected to a local magnetic field that varies in magnitude and direction, so it is not possible to specify the magnetic field strength at which the measurement is made.4 1.2.5?Test Method 5?Vibrating Sample Magnetometry is suitable for materials with relative permeabilities between 1.0 and 4.0. This test method permits the user to select the magnetic field strength at which the permeability is to be measured. 1.3?Materials typically tested by these methods such as austenitic stainless steels may be weakly ferromagnetic. That is, the magnetic permeability is dependent on the magnetic field strength. As a consequence, the results obtained using the different methods may not closely agree with each other. When using Methods 1 and 5, it is imperative to specify the magnetic field strength or range of magnetic field strengths at which the permeabilities have been determined. 1.4?The values and equations stated in customary (cgs-emu and inch-pound) or SI units are to be regarded separately as standard. Within this standard, SI units are shown in brackets except for the sections concerning calculations where there are separate sections for the respective unit systems. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 29.030 : 자성 재료 |
| 페이지수 | 8 |
| Edition | 21 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A342/A342M-21 | Standard Test Methods for Permeability of Weakly Magnetic Materials | 2021-02-01 | 표준 |
| 2 | ASTM A342/A342M-21 REDLINE | Standard Test Methods for Permeability of Weakly Magnetic Materials | 2021-02-01 | 표준 |
| 3 | ASTM A342/A342M-14 | Standard Test Methods for Permeability of Weakly Magnetic Materials | 2014-05-01 | 구판 |
| 4 | ASTM A342/A342M-14 REDLINE | Standard Test Methods for Permeability of Weakly Magnetic Materials | 2014-05-01 | 구판 |
| 5 | ASTM A342/A342M-04(2012) | Standard Test Methods for Permeability of Feebly Magnetic Materials | 2012-05-01 | 구판 |
| 6 | ASTM A342/A342M-04 | Standard Test Methods for Permeability of Feebly Magnetic Materials | 2004-10-01 | 구판 |
| 7 | ASTM A342/A342M-99 | Standard Test Methods for Permeability of Feebly Magnetic Materials | 1999-10-10 | 구판 |
관련상품이 존재하지 않습니다.
SPS-KEA065-IEC 60770-2-6425 - 산업용 공정 제어 시스템에서 사용을 위한 발신기－제2부：검사 및 일상 시험 지침 상세보기
SPS-KEA065-IEC 60770-1-6464 - 산업용 공정 제어 시스템에서 사용하기 위한 발신기－제1부：성능 평가 방법 상세보기
JIS G 3454:2017/AMENDMENT 1:2019 - Carbon steel pipes for pressure service (Amendment 1) 상세보기
JIS G 3454:2017 - Carbon steel pipes for pressure service 상세보기
ASTM A572/A572M-04 - Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
