관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practices for Sampling Metal Powders
| 분야 | 02.05 : 금속 및 무기질 피막, 금속분말 |
|---|---|
| 적용범위 | 1.1 These practices cover sampling methods used to collect a small quantity of metal powder that is as representative of the entire starting material as possible, and detail the procedures that are recommended for reducing this quantity into smaller test portions on which chemical, physical, and mechanical property data may be determined. 1.2 Several sampling practices are described, depending on their applicability to the conditions of storage and transport of the sampled powders: 1.2.1 Practice 1A (Described in Section 6)—Applicable to sampling moving powders, as when being transferred from one container to another or to a process stream; or when falling from a conveyor; or in a moving process stream. This is the preferred practice for obtaining the several increments that are combined to form the gross sample. 1.2.2 Practice 1B (Described in Section 7)—Applicable to sampling powders that have already been packaged for transport, as in a bag or drum. A hollow tubular slot sampler is the recommended way to sample these packaged powders to obtain the increments (7.1.1). Alternatively, when other methods are not possible or available, a procedure specified here (7.1.2) may be used to randomly scoop samples from the powder, using a scoop of specified material and configuration. 1.2.3 Practice 2 (Described in Section 8)—Applicable to obtaining test portions from the composite sample. For larger quantities of powder, a chute splitter is generally used, while a spinning riffler is used for smaller quantities. 1.3 These practices apply to particulate materials or mixtures of particulates with particle sizes generally less than one millimetre and include mixtures containing lubricant, with or without other non-metallic additives, that are ready for compacting. 1.4 These practices do not cover the sampling of flake powders or pastes. For procedures on the sampling and testing of flake metal powders and pastes, refer to Test Methods D480. 1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.160 : 동력 금속학 |
| 페이지수 | 7 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B215-20 | Standard Practices for Sampling Metal Powders | 2020-11-01 | 표준 |
| 2 | ASTM B215-20 REDLINE | Standard Practices for Sampling Metal Powders | 2020-11-01 | 표준 |
| 3 | ASTM B215-15 | Standard Practices for Sampling Metal Powders | 2015-10-01 | 표준 |
| 4 | ASTM B215-15 REDLINE | Standard Practices for Sampling Metal Powders | 2015-10-01 | 표준 |
| 5 | ASTM B215-10 | Standard Practices for Sampling Metal Powders | 2010-12-01 | 구판 |
| 6 | ASTM B215-08 | Standard Practices for Sampling Metal Powders | 2008-11-01 | 구판 |
| 7 | ASTM B215-04 | Standard Practices for Sampling Metal Powders | 2004-10-01 | 구판 |
| 8 | ASTM B215-96 | Standard Practices for Sampling Finished Lots of Metal Powders | 1996-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM B822-20 - Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by Light Scattering 상세보기
ASTM A370-20 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products 상세보기
ASTM F3434-20 - Guide for Additive manufacturing – Installation/Operation and Performance Qualification (IQ/OQ/PQ) of Laser-Beam Powder Bed Fusion Equipment for Production Manufacturing 상세보기
ASTM B962-17 - Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle 상세보기
ASTM B311-17 - Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
