관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame-Resistant Materials for Clothing with Continuous Heating
| 분야 | 11.03 : 작업장에서의 건강 및 안전; 보호의복 |
|---|---|
| 적용범위 | 1.1 This test method measures the non-steady state heat transfer through flame-resistant materials for clothing subjected to a continuous, combined convective and radiant heat exposure. 1.1.1 This test method is not applicable to materials that are not flame resistant. Note 1: The determination of a material’s flame resistance shall be made prior to testing and done according to the applicable performance or specification standard, or both, for the material’s end-use. 1.1.2 This test method does not predict a material’s skin burn injury performance from the specified thermal energy exposure. It does not account for the thermal energy contained in the test specimen after the exposure has ceased. Note 2: See Appendix X4 for additional information regarding this test method and predicted skin burn injury. 1.2 This test method is used to measure and describe the response of materials, products, or assemblies to heat under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound or other units that are commonly used for thermal testing. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 13.340.10 : 보호의 |
| 페이지수 | 12 |
| Edition | 08(2020) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F2700-08(2020) | Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame-Resistant Materials for Clothing with Continuous Heating | 2020-10-01 | 표준 |
| 2 | ASTM F2700-08(2013) | Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing with Continuous Heating | 2013-06-01 | 구판 |
| 3 | ASTM F2700-08 | Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing with Continuous Heating | 2008-07-01 | 구판 |
관련상품이 존재하지 않습니다.
BS EN 388:2016+A1:2018 - Protective gloves against mechanical risks. 상세보기
BS EN 943-1:2015+A1:2019 - Protective clothing against dangerous solid, liquid and gaseous chemicals, including liquid and solid aerosols. Performance requirements for Type 1 (gas-tight) chemical protective suits. 상세보기
ASTM F1790/F1790M-15(2021) - Standard Test Method for Measuring Cut Resistance of Materials Used in Protective Clothing with CPP Test Equipment 상세보기
ASTM F739-20 - Standard Test Method for Permeation of Liquids and Gases Through Protective Clothing Materials Under Conditions of Continuous Contact 상세보기
NFPA 2112 18th Edition, August 11, 2020 - STANDARD ON FLAME-RESISTANT CLOTHING FOR PROTECTION OF INDUSTRIAL PERSONNEL AGAINST SHORT-DURATION THERMAL EXPOSURES FROM FIRE 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
