관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the temperature at which plastics and elastomers (as defined by Terminology D883) exhibit brittle failure under specified impact conditions. Two routine inspection and acceptance procedures are also provided. Note 1: When testing rubbers for impact brittleness use Test Method D2137. When testing plastic sheeting for impact brittleness, use Test Method D1790. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 Due to the potential safety and environmental hazards associated with mercury-filled thermometers, the use of alternative temperature measuring devices (such as thermocouples and RTDs) is encouraged. Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2: This test method and ISO 974 address the same subject matter, but differ in technical content. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 |
83.060 : 고무
83.080.01 : 플라스틱 일반 |
| 페이지수 | 7 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D746-24 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2024-05-01 | 표준 |
| 2 | ASTM D746-24 REDLINE | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2024-05-01 | 표준 |
| 3 | ASTM D746-20 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2020-06-01 | 구판 |
| 4 | ASTM D746-20 REDLINE | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2020-06-01 | 구판 |
| 5 | ASTM D746-14 REDLINE | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2014-12-01 | 구판 |
| 6 | ASTM D746-14 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2014-12-01 | 구판 |
| 7 | ASTM D746-13 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2013-06-01 | 구판 |
| 8 | ASTM D746-07 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2007-03-01 | 구판 |
| 9 | ASTM D746-04 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 2004-05-01 | 구판 |
| 10 | ASTM D746-98e1 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact | 1998-07-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials 상세보기
ASTM D256-10(2018) - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics 상세보기
AWS D1.1/D1.1M 24th Edition, 2020 - Structural Welding Code—Steel 상세보기
ASHRAE GUIDELINE 23, 2016 Edition 20, 2009 - Guideline for the Design and Application of Heating, Ventilation, and Air-Conditioning Equipment for Rail Passenger Vehicles 상세보기
ASHRAE STD 37 2009 Edition, June 20, 2009 - METHODS OF TESTING FOR RATING ELECTRICALLY DRIVEN UNITARY AIR-CONDITIONING AND HEAT PUMP EQUIPMENT 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
