관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys
| 분야 | 02.02 : 알루미늄 및 마그네슘 합금 |
|---|---|
| 적용범위 | 1.1 This practice establishes the controls required for extrusion press solution heat treatment of the 6xxx and 7xxx series aluminum alloys in Table 1 when ASTM material specifications allow use of this process in lieu of furnace solution heat treatment. For the alloys listed in Table 1, this practice is an alternate process to solution heat treatment in a furnace, such as specified in Practice B918/B918M for the attainment of T3, T4, T6, T7, T8, and T9-type tempers (see ANSI H35.1/H35.1M). 1.2 This practice applies only to extrusion press solution heat treatment for aluminum alloys. Precipitation hardening (aging) and annealing processing and equipment calibration shall meet the practice and requirements of Practice B918/B918M. 1.3 The values stated in either Metric SI units or US Customary units are to be regarded separately as standard. The Metric SI units are shown in brackets or in separate tables. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.120.10 : 알루미늄 및 알루미늄합금 |
| 페이지수 | 5 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B807/B807M-20 REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys | 2020-05-01 | 표준 |
| 2 | ASTM B807/B807M-20 | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys | 2020-05-01 | 표준 |
| 3 | ASTM B807/B807M-13 REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys | 2013-06-01 | 구판 |
| 4 | ASTM B807/B807M-13 | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys | 2013-06-01 | 구판 |
| 5 | ASTM B807/B807M-06 | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys | 2006-03-15 | 구판 |
관련상품이 존재하지 않습니다.
DIN EN 2032-2:1994-05 - Aerospace series; metallic materials; part 2: coding of metallurgical condition in delivery condition; German version EN 2032-2:1994 상세보기
DIN EN 2004-1:1993-09 - Aerospace series; test methods for aluminium and aluminium alloy products; part 1: determination of electrical conductivity of wrought aluminium alloys; German version EN 2004-1:1993 상세보기
DIN EN 2002-7:1999-05 - Aerospace series - Metallic materials; test methods - Part 7: Hardness test 상세보기
BS EN 2002-1:2005 - Aerospace series. Metallic materials. Test methods. Tensile testing at ambient temperature. 상세보기
ASTM B918/B918M-20a - Standard Practice for Heat Treatment of Wrought Aluminum Alloys 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
