관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Secondary Calibration of Acoustic Emission Sensors
| 분야 | 03.03 : 비 파괴검사 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This practice covers requirements for the secondary calibration of acoustic emission (AE) sensors. The secondary calibration yields the frequency response of a sensor to waves of the type normally encountered in acoustic emission work. The source producing the signal used for the calibration is mounted on the same surface of the test block as the sensor under testing (SUT). Rayleigh waves are dominant under these conditions; the calibration results represent primarily the sensor's sensitivity to Rayleigh waves. The sensitivity of the sensor is determined for excitation within the range of 100 kHz to 1 MHz. Sensitivity values are usually determined at frequencies approximately 10 kHz apart. The units of the calibration are volts per unit of mechanical input (displacement, velocity, or acceleration). 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 17.140.01 : 음향 측정 및 소음 감소 일반 |
| 페이지수 | 8 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E1781/E1781M-20 | Standard Practice for Secondary Calibration of Acoustic Emission Sensors | 2020-04-01 | 표준 |
| 2 | ASTM E1781/E1781M-20 REDLINE | Standard Practice for Secondary Calibration of Acoustic Emission Sensors | 2020-04-01 | 표준 |
| 3 | ASTM E1781/E1781M-19 | Standard Practice for Secondary Calibration of Acoustic Emission Sensors | 2019-07-01 | 구판 |
| 4 | ASTM E1781/E1781M-19 REDLINE | Standard Practice for Secondary Calibration of Acoustic Emission Sensors | 2019-07-01 | 구판 |
| 5 | ASTM E1781/E1781M-13 REDLINE | Standard Practice for Secondary Calibration of Acoustic Emission Sensors | 2013-06-01 | 구판 |
| 6 | ASTM E1781/E1781M-13 | Standard Practice for Secondary Calibration of Acoustic Emission Sensors | 2013-06-01 | 구판 |
관련상품이 존재하지 않습니다.
DIN EN 203-2-1:2019-03 - Gas heated catering equipment - Part 2-1: Specific requirements - Open burners and wok burners; German and English version prEN 203-2-1:2019 상세보기
ASTM E569/E569M-20 - Standard Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation 상세보기
ASTM E2374-16 - Standard Guide for Acoustic Emission System Performance Verification 상세보기
ASTM E543-15 - Standard Specification for Agencies Performing Nondestructive Testing 상세보기
CSA 4.1:19/ANSI Z21.10.1:19 - Gas water heaters, volume I, storage water heaters with input ratings of 75,000 Btu per hour or less, Includes Errata (2020) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
