관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Additive manufacturing ? Material extrusion-based additive manufacturing of plastic materials ? Part 1: Feedstock materials
| 분야 | 10.04 : 전자 |
|---|---|
| 적용범위 | 1.1 This document describes a method for defining requirements for plastic materials used in extrusion-based additive manufacturing (AM) processes. Materials include unfilled, filled, and reinforced plastic materials suitable for processing into parts. These materials can also contain special additives (e.g., flame retardants, stabilizers, etc.). Processes include all material extrusion-based AM processes. This document is intended for use by manufacturers of materials, feedstocks, or plastic parts or any combination of the three using material extrusion-based AM. Note 1: In some cases, material manufacturers can also be feedstock manufacturers. In other cases, a material manufacturer can supply materials (example: pellets) to a feedstock manufacturer (example: convertor of pellets into filaments). This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 4 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM ISO/ASTM52903-1-20 | Additive manufacturing ? Material extrusion-based additive manufacturing of plastic materials ? Part 1: Feedstock materials | 2017-10-01 | 표준 |
ISO/ASTM 52903-1:2020 - Additive manufacturing — Material extrusion-based additive manufacturing of plastic materials — Part 1: Feedstock materials 상세보기
ASTM ISO/ASTM52903-2-20 - Additive manufacturing ? Material extrusion-based additive manufacturing of plastic materials ? Part 2: Process equipment 상세보기
ISO/ASTM 52903-2:2020 - Additive manufacturing — Material extrusion-based additive manufacturing of plastic materials — Part 2: Process equipment 상세보기
ASTM ISO/ASTM52901-16 - Standard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts 상세보기
ASTM ISO/ASTM52910-18 - Additive manufacturing ? Design ? Requirements, guidelines and recommendations 상세보기
ASTM ISO/ASTM52911-2-19 - Additive manufacturing — Design — Part 2: Laser-based powder bed fusion of polymers 상세보기
ASTM ISO/ASTM52903-2-20 - Additive manufacturing ? Material extrusion-based additive manufacturing of plastic materials ? Part 2: Process equipment 상세보기
ASTM ISO/ASTM52950-21 - Additive manufacturing ? General principles ? Overview of data processing 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
