관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels
| 분야 | 05.06 : 기체화 연료; 석탄 및 코커스 |
|---|---|
| 적용범위 | 1.1 This practice covers procedures for calculating heating value, relative density, and compressibility factor at base conditions (14.696 psia and 60°F (15.6°C)) for natural gas mixtures from compositional analysis.2 It applies to all common types of utility gaseous fuels, for example, dry natural gas, reformed gas, oil gas (both high and low Btu), propane-air, carbureted water gas, coke oven gas, and retort coal gas, for which suitable methods of analysis as described in Section 6 are available. Calculation procedures for other base conditions are given. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 75.160.30 : 기체 연료 |
| 페이지수 | 9 |
| Edition | 98(2017)e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3588-98(2024)e1 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels | 2024-05-01 | 표준 |
| 2 | ASTM D3588-98(2017) | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels | 2017-04-01 | 구판 |
| 3 | ASTM D3588-98(2017)e1 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels | 2017-04-01 | 구판 |
| 4 | ASTM D3588-98(2011) | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels | 2011-11-01 | 구판 |
| 5 | ASTM D3588-98(2003) | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels | 2003-05-10 | 구판 |
| 6 | ASTM D3588-98 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels | 1998-05-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D6228-19 - Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection 상세보기
ASTM D2163-14(2019) - Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography 상세보기
ASTM D5454-11(2020) - Standard Test Method for Water Vapor Content of Gaseous Fuels Using Electronic Moisture Analyzers 상세보기
ASTM D1838-20 - Standard Test Method for Copper Strip Corrosion by Liquefied Petroleum (LP) Gases 상세보기
ASTM D651(1984 Edition) - STANDARD TEST METHOD FOR TENSILE STRENGTH OF MOLDED ELECTRICAL INSULATING MATERIALS 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
