관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
| 분야 | 04.02 : 콘크리트 및 골재 |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving. 1.2 Some specifications for aggregates which reference this test method contain grading requirements including both coarse and fine fractions. Instructions are included for sieve analysis of such aggregates. 1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. Specification E11 cites the following with respect to SI units versus inch-pound units as standard. “The values stated in SI units shall be considered standard for the dimensions of the sieve cloth openings and the wire diameters used in the sieve cloth. The values stated in inch-pound units shall be considered standard with regard to the sieve frames, pans,” and covers. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.100.30 : 콘크리트 및 콘크리트 제품 |
| 페이지수 | 5 |
| Edition | 19 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C136/C136M-19 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates | 2019-12-01 | 표준 |
| 2 | ASTM C136/C136M-19 REDLINE | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates | 2019-12-01 | 표준 |
| 3 | ASTM C136/C136M-14 REDLINE | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates | 2014-12-01 | 구판 |
| 4 | ASTM C136/C136M-14 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates | 2014-12-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM C142/C142M-17 - Standard Test Method for Clay Lumps and Friable Particles in Aggregates 상세보기
ASTM A123/A123M-17 - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products 상세보기
ASTM C33/C33M-18 - Standard Specification for Concrete Aggregates 상세보기
ASTM A572/A572M-18 - Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 상세보기
ASTM C88/C88M-18 - Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
