관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Hardened Steel Washers Inch and Metric Dimensions
| 분야 | 01.09 : 비철화스너 (구름요소베어링) |
|---|---|
| 적용범위 | 1.1 This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1/4 through 4 in. and M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A354, A449, A563, A563M, F959/F959M, and F3125. 1.2 The washers are designated by type denoting the material, by style denoting the shape, and by inch or metric dimensions. 1.2.1 The types of washers covered are: 1.2.1.1 Type 1—Carbon steel. 1.2.1.2 Type 3—Weathering steel. 1.2.1.3 This specification provides for furnishing Type 3 to chemical composition or a Corrosion Index (CRI) of 6 or higher at the suppliers option. 1.2.2 The styles of washers covered are: 1.2.2.1 Circular—Circular washers in nominal sizes 1/4 through 4 in. and M12 through M100 suitable for applications where sufficient space exists and angularity permits. 1.2.2.2 Beveled—Beveled washers are square or rectangular, in nominal sizes 1/2 through 11/2 in., M12 through M16, with a beveled 1 to 6 ratio surface for use with American standard beams and channels. 1.2.2.3 Clipped—Clipped washers are circular or beveled for use where space limitations necessitate that one side be clipped. 1.2.2.4 Extra Thick—Extra thick washers are circular washers in nominal sizes 1/2 through 4 in., with a nominal thickness of 5/16 in. suitable for structural applications with oversized holes. 1.3 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein. 1.4 The values stated in either inch-pound units for inch fasteners and SI units for metric fasteners and are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 21.060.20 : 너트 |
| 페이지수 | 8 |
| Edition | 19 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F436/F436M-24 | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2024-11-01 | 표준 |
| 2 | ASTM F436/F436M-24 REDLINE | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2024-11-01 | 표준 |
| 3 | ASTM F436/F436M-19 | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2019-12-01 | 구판 |
| 4 | ASTM F436/F436M-19 REDLINE | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2019-12-01 | 구판 |
| 5 | ASTM F436/F436M-18a REDLINE | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2018-09-01 | 구판 |
| 6 | ASTM F436/F436M-18a | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2018-09-01 | 구판 |
| 7 | ASTM F436/F436M-18 | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2018-06-01 | 구판 |
| 8 | ASTM F436/F436M-16 | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions | 2016-09-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM A194/A194M-20a - Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both 상세보기
ASTM A193/A193M-20 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications 상세보기
ASTM F3125/F3125M-19e2 - Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength 상세보기
ASTM A123/A123M-17 - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products 상세보기
ASTM A354-17e2 - Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
