관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings
| 분야 | 06.01 : 페인트-화학적, 물리적, 광학적특성 시험; 현상 |
|---|---|
| 적용범위 | 1.1 This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in fluorescent UV and condensation devices conducted according to Practices G151 and G154. This practice also covers the preparation of test specimens, and the evaluation of test results. Table 1 describes commonly used test conditions. Note 1: Previous versions of this practice referenced fluorescent UV devices described by Practice G53, which described very specific equipment designs. Practice G53 has been withdrawn and replaced by Practice G151, which describes performance criteria for all exposure devices that use laboratory light sources, and by Practice G154, which gives requirements for exposing nonmetallic materials in fluorescent UV devices. Note 2: ISO 11507:1997 also describes fluorescent UV-condensation exposures of paints and coatings. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 87.040 : 페인트 및 니스 |
| 페이지수 | 6 |
| Edition | 11(2019)e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D4587-23 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2023-06-01 | 표준 |
| 2 | ASTM D4587-23 REDLINE | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2023-06-01 | 표준 |
| 3 | ASTM D4587-11(2019)e1 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2019-12-01 | 구판 |
| 4 | ASTM D4587-11 REDLINE | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2011-06-01 | 구판 |
| 5 | ASTM D4587-11 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2011-06-01 | 구판 |
| 6 | ASTM D4587-05 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2005-07-01 | 구판 |
| 7 | ASTM D4587-91 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2001-07-10 | 구판 |
| 8 | ASTM D4587-01 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings | 2001-07-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D523-14(2018) - Standard Test Method for Specular Gloss 상세보기
ASTM D2244-16 - Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates 상세보기
ASTM D1729-16 - Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials 상세보기
ASTM D3359-17 - Standard Test Methods for Rating Adhesion by Tape Test 상세보기
ASTM D4145-10(2018) - Standard Test Method for Coating Flexibility of Prepainted Sheet 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
